搜索资源列表
2KH-square-wave-generator
- 利用定时器TMR2与周期寄存器PR2配合工作,从引脚RD0上输出一个占空比为50 的对称方波,该方波信号的周期为0.5ms。可以利用示波器观察和验证该波形,单片机初次加电或者复位之后,发光二极管LED7不停地闪烁,LED0亦被点亮(实际上,LED0在快速闪烁,只不过由于其频率过高人眼不易察觉),表明方波发生器正常工作。-Timer TMR2 Period register, PR2 work with, from the pin RD0, output a 50 duty cycle symm
Mini51_Os
- 基于51单片机和CPLD实现的示波器,实现数据采集与显示,测量。含有完整的介绍资料和期间选择及原理图。-Based on 51 MCU and CPLD implementation oscilloscope, data acquisition and display, measurement. Containing a complete introduction and during the selection and schematics.
12864(KS0108)
- 单片机KS0108 12864液晶屏做的示波器驱动部分。。。全部源码-Microcontroller KS0108 12864 oscilloscope driven LCD do. . . All source code. .
DIY_digital-oscilloscope
- 用单片机开发数字示波器的途径和方法。。。很值得一看-Microcontroller development ways and means of the digital oscilloscope. . . It is worth a visit
little_software
- 单片机开发常用到的小工具,比如波特率计算,虚拟示波器,电阻值计算-Commonly used microcontroller development tools, such as baud rate calculation, virtual oscilloscope, resistance value calculated
Dos_Pro---8.18
- 简易数字示波器,从AD接受双通道数据,存入内部fifo,并通过串口传至单片机实现波形显示-Simple digital oscilloscope, from AD to accept dual-channel data stored in the internal fifo waveform display and transmitted to the microcontroller through the serial port
STC_delay
- STC12C5A系列单片机精确延时函数分析,带计算模板,毫秒级延时和微秒级延时,适用于STC其他单片机分析,符合示波器观察结果。-Precision delay STC12C5A Series MCU function analysis, with calculation template, millisecond latency and microsecond delay applies to STC microcontroller analysis, in line with the osc
chuangxing
- 配置CCP1模块使之工作于PWM模式,并初始化周期和占空比。单片机的UART接口工作于全双工异步模式,1个起始位,8个数据位,1个停止位,波特率为9600,并开启接收中断,与PC机通信。编写程序实现功能:当UART接收到命令“S”时,LCD上显示“PWM Start”, PWM开始工作。当UART接收到命令“U”时,占空比增加,当UART接收到命令“D”时,占空比减少,并在LCD上显示占空比。当UART接收到命令“P”时, PWM停止工作,LCD上显示“PWM Stop”。并用示波器观察PWM输
c_language_Drawing-curves
- 基于单片机C语言实现液晶屏的曲线显示,可用于示波器等系统。-SCM C language-based curve of the LCD display can be used for systems such as an oscilloscope.
STC12some-device-driver
- 里面含有一些STC12系列单片机常用的硬件驱动程序和片上资源驱动程序。工作在11.0592MHZ可以直接使用。如12864的串口方式驱动,1602驱动,18B20驱动,DHT11驱动,STC片上EEPROM/ADC/PWM等驱动程序,还包括一些经过本人用示波器侧过的STC12系列单片机在11.0592MHZ下的软件延时子函数。这些东西对你平时开发会大有帮助。-failed to translate
shuzilvboqi
- 基于单片机的简单数字示波器的制作,能简单实现波形的输出与显示。-Making simple digital oscilloscope based on single chip, can realize a simple waveform output and display.
BOSC
- 基于飞利浦的单片机P89LPC938的手机虚拟示波器源程序-Philips P89LPC938 microcontroller-based mobile virtual oscilloscope source
sanjiaobo
- 51单片机中利用PCF8591进行D/A转换在示波器中显示三角波-51 MCU PCF8591 using the D/A converter in the oscilloscope display triangular wave
juchibo
- 基于51单片机开发板,利用PCF8591将电压值进行A/D转换,在示波器上显示锯齿波-Based on 51 MCU development board, the use of the voltage value PCF8591 A/D conversion, displayed on the oscilloscope sawtooth
Oscilloscope_V1.00_2012_7_13
- 单片机 C8051F120 实现简易示波器功能,频率范围1hz~1Mhz,可在LCD上显示波形,串口发送峰峰值,有效值,频率-MCU C8051F120 achieve simple oscilloscope
achieve-DA-function
- 单片机去控制PCF8591T去实现DA功能。 这个代码也要在示波器上才能观测到,DA输出一个正弦波。-Microcontroller to control PCF8591T to achieve DA function. This code also can be observed on an oscilloscope, DA output a sine wave.
2013.7.20
- 利用msp430单片机对输入信号进行采样,并在12864液晶上实时显示波形和频率、幅值,最后送DAC输出至示波器还原,已通过实际测试-Use msp430 microcontroller input signal is sampled and 12864 on the real-time waveform and frequency, amplitude, and finally sent to the DAC output to the oscilloscope reduction, have
89C5-Virtual-digital-oscilloscope
- 该程序利用89c51单片机和lcd液晶显示实现简易的数字示波器,可以显示输入的方波、正弦等信号。-The program using 89 c51 and LCD liquid crystal display a simple digital oscilloscope, can display the input square wave and sine signal.
shiboqi
- 使用stc12单片机实现的示波器程序,采用12864的竖屏显示来加快反应速度。希望高手能帮忙改进-Oscilloscope using stc12 MCU program, using 12,864 vertical screen display to accelerate the reaction rate. I hope you can help improve
shiyan3
- 开发环境:unSP IDE 2.0.0 实验目的: 1)了解SPCE061 PLL 振荡器的功能及其应用。 2)掌握系统时钟单元P_SystemClock的设置方法。 3)熟悉系统时钟和CPU时钟频率的编程方法。 实验设备: 1)装有µ ’nSP™ IDE仿真环境的PC机一台。 2)µ ’nSP™ 十六位单片机实验箱一个。 3)示波器一台。 实验原理: 在SPCE061A内,P_SystemCloc