搜索资源列表
51测试硬件程序
- 本程序是一个传输控制器的硬件测试程序,用的c51芯片,硬件包括观光电输入、继电器输出、串行通讯等,全部由测试程序测试。大家可以参考一下。-this program is a transmission controller hardware testing procedures, the decoder chip, hardware includes sightseeing -- input, output relays, serial communications, all from the t
Relay_Function_Test
- 此程序为本人在公司开发的继电器功能测试仪,用KEIL C编写。可以测试线圈电阻,接触电阻,吸合释放电压,时间等参数。采用WINBONG W77E58 单片机。
Relay_Function_Tester_Circuit
- 此为继电器功能测试电路图DDB文件。对应源码为Relay_Function_Tester. keil c51 编写。
led
- ARM7开发板测试程序,实现流水灯,继电器,蜂鸣器,数码管,按键等器件的操作-ARM7 development board testing procedures, to achieve water lamp, relay, buzzer, digital tube, keys and other devices operate
单片机驱动的继电器电路
- 这是一个用单片机驱动继电器的继电器部分电路。这样的东东网上很多,问题也很多,这个电路本人测试过。并在实际应用中经常使用!
jidianqi
- 用此源代码,可以用于继电器测试仪的开发,通过继电器测试仪可以测试继电器的状态等-Use this source code, can be used to relay tester development, through the relay tester can test the status of relays, etc.
pull_in_test
- 此仪器可以测试继电器的吸合电压,释放电压,完全吸合电压,完全释放电压。在KEIL UVISION环境下采用C51编程,通过3位LED显示结果。内附电路原理图。-This instrument can test the relay pull-in voltage, release voltage, full pull-in voltage, fully release voltage. KEIL UVISION in C51 programming environment used by the
TV_power_tester
- MCU控制继电器做的电源老化测试程序.每次测100次-MCU Control Relay aging power to do testing procedures. Each measuring 100 times
7BLOCKERSTEST
- 基于凌阳61开发板,通过继电器,步进电机,直流电机,外部显示完成柜门耐久度的测试。步进电机模拟人手动作转动把手开锁并利用直流电机开关门,并通过外部动态LED显示完成测试。-based on Sunplus 61 development board, through the relays, stepper motors, DC motors, the external display doors complete durability testing. Stepper motor rotation
Speed-test-equipment
- 风速测试仪,有单片机控制器、按键输入、测试风机、LCD指示器、继电器输出、蜂鸣器输出及电源等七部分组成。-Wind speed tester, there are single-chip controller, keystrokes, testing fan, LCD indicator, relay output, buzzer output and power seven parts.
usingAT89S51controlrelaytest
- 磁保持继电器通断测试程序,采用AT89S51控制。-Magnetic self-perpetuating relay-off test procedure, using AT89S51 control.
Remote_program
- 为配套的红外线遥控(P3.7)显示数码管1234567890的程序 遥控器控制30个io的led点亮,可由此控制继电器实现家电的遥控 遥控器控制显示0123456789abcdef数据保持 遥控器测试程序按任意键试验版数码管指示灯闪烁。任意遥控器均可-Infrared remote control for the matching (P3.7) shows the digital control procedures 1234567890 remote control 30 io
relay
- 基于lpc2368的继电器参数测试仪。主要测试继电器的吸合电压,吸合时间,释放电压,释放时间和接触电阻-Relay parameters on lpc2368 tester. Pull the main relay test voltage, the pull of time, release voltage, release time and the contact resistance
yaokong
- 为配套的红外线遥控(P3.7)显示数码管1234567890的程序 n6221c.asm 倚天版遥控器控制30个io的led点亮,可由此控制继电器实现家电的遥控 n6221b.asm 倚天版遥控器控制显示0123456789abcdef数据保持 yaokong.asm 遥控器测试程序按任意键试验版数码管指示灯闪烁。任意遥控器均可!-Infrared remote control for the matching (P3.7) shows the digital control pr
relay-test
- 继电器的测试实验,初学者的好帮手呀,-Relay switch control experiments
stc15单片机测试程序V1.0版
- stc15单片机测试程序V1.0版 1.LED灯2.独立按键3.18b20 4.1602 5.12864 6.AD 7.PCF8563 8.红外接收 9.步进电机 10.串口 11.蜂鸣器 12.继电器 13.矩阵按键 14.数码管 15.直流电机
数码管测试程序1.1
- 控制电机岩石正反转 ,带延时 防止电机烧毁(Control motor rock positive reversal, delay to prevent the motor burned.)
SI432通信测试
- 用15F2K60S2进行继电器控制,SI4432通讯测试,(Relay control with 15F2K60S2, SI4432 communication test)
51单片机数码管测试
- 自己前些天安装了一个6位数码管带4个继电器采用4个独立按钮控制数码管的单片机,其中数码管安装后,就是采用这个方法检测的。采用6位共阳数码管,位控制采用74hc38译码器,段控制采用74HC245,如果能够显示543210,那就说明单片机数码管硬件部分没问题了。(I installed a 6 bit digital tube with 4 relays the other day, and 4 independent buttons to control the digital tube mic
kjh
- 对继电器性能做了检测,吸合电压释放电压动作时间,用了PWM波(The performance of the relay is tested)