搜索资源列表
网络通信处理器S3C4510B的网口驱动设计.
- 网络通信处理器S3C4510B的网口驱动设计（ARM）- Network correspondence processor S3C4510B net mouth actuation design (ARM)
kernel-yizhi
- 将内核移植到s3c2410上，并加上了网口驱动
DM9000A
- 这是基于samsung s3c2413 的DM9000网口驱动
rtl8019as网卡驱动程序
- 该文件是基于三星44b0芯片arm嵌入式系统的rtl8019网口的驱动程序-The document is based on Samsung 44b0 chip embedded systems arm of the mouth rtl8019 Network Driver
ethernet_328
- 基于arm的ethernet_328网口驱动程序，已经经过调试了，可以直接移植。-ethernet_328 based arm of the network driver I have read debugging, it can direct transplantation.
Ether.rar
- DM642网口驱动例程。可参照此例程开发网口的应用,I drive routine DM642 network. Refer to the routine application of open network port
EasyWEB
- LPC23XX系列的网口驱动例程， 在LPC2478也可以运行。-LPC ON CHIP, enet controler driver code
CONFIG850
- 850双网口驱动BSP包VXWORKS用与开发,测试过好用-VXWORKS BSP FOR MPC850
rndis_driver
- 基于usb的模拟网口驱动 rndis 实例，程序经验证，wince平台-Based on the simulation network port driver usb rndis instance, procedures proven, wince platform
dm642networkdriver(ndk)
- dm642网口驱动程序，使用ndk模块，调试后的可用代码-dm642 network port driver, using the ndk module, debug code can be used after
Linux_serial_network_src
- linux下将串口虚拟成网口驱动程序，c语言源代码-Linux serial to network
prc6000_emac_linux
- percello系列芯片prc6xxx网口驱动，synopsis架构-The Linux driver for prc6xxx eMAC using the synopsis architecture.
W5300-Driver-Keil-C
- W5300网口驱动，硬件实现TCP/IP协议，便于实现网络传输-The W5300 Ethernet port drivers, the hardware implementation of the TCP/IP protocol, and easy to realize network transmission
C6x_Source
- TI C64x参考程序，代码 内容包括： C语言正弦函数程序 汇编语言正弦函数程序 EMIFA_SDRAM配置程序 FLASH读写程序 EDMA_EMIFA_FIFO配置程序 McBSP_RS232通讯程序 McBSP_SPI_ AD7843驱动程序 HPI数据传输程序 VPORT驱动程序 网口驱动程序 C6416_C68001配置程序 双目视觉测距程序 声源定位程序-The TI C64x reference program, code
ads827x_boot
- 本工程是MPC8272的BSP包。包括网口驱动、Flash驱动和SDRAM驱动等。足以支持简单工程需要的BSP配置。-This project is the MPC8272 BSP package. Including network port driver, Flash driver and SDRAM driver. Enough to support simple engineering need BSP configuration.
LPC3250_KSZ8041NL_UDP
- LPC3250 基于UCOS——II的UDP网口驱动程序。该代码已测试通过，很稳定，系统的速度能够在1到3.5M之间。-LPC3250 driver UCOS- II-based UDP network port. The code has been tested by very stable, and the speed of the system can be between 1 to 3.5M.
dp83848-with-lpc1768
- ARM芯片lpc1768、网口驱动芯片DP83848时的以太网通信程序-Ethernet communication program with ARM chips lpc1768 and drive chip DP83848
ethernet_loopback
- 通过FPGA驱动千兆以太网口，完成SPARTAN6上的UDP数据包闭环测试，即通过网口发送数据包到FPGA，FPGA内部将接收到的数据返回到PC机，建议测试之前添加ARP静态绑定，FGPA内部的IP以及MAC地址在ROM里的COE文档里可以看到，发送端添加了CRC以及整体CHECKSUM的计算(Driven by FPGA Gigabit Ethernet port, UDP SPARTAN6 data packet on the closed loop test, through the ne
STM32利用网口CH395传输数据源码及资料
- 使用MDK5编写的程序，利用STM32F103驱动CH395模块利用网口和电脑之间通信，还包含了相关的资料(Using the program written in MDK5, using the STM32F103 to drive the CH395 module to communicate between the network and the computer, the related information is also included.)
fm3_dual_ethernet_rt-thread
- 富士通 FM3 系列双网口驱动 rt-thread 嵌入式实时系统 框架程序(Fujitsu FM3 Series RT-thread Embedded Real-time System Framework Program Driven by Dual-Port)