搜索资源列表
Test_EXTInterrupt_FIQ
- 实验方法: 1写flash 烧flash的时候采用默认的配置 2然后在JTAG方式下面调试 按key1 key 2 3 4 发光管亮灭-Experimental methods: 1 write flash burn flash when using the default configuration of 2 and then in the JTAG debug mode by following key1 key 2 3 4 LED light out
linuxmakemenuconfig
- 在linux下使用make menuconfig配置uclinux for s3c44b0的视频教程。-In linux to use make menuconfig to configure uclinux for s3c44b0 the video tutorial.
0904071154
- 基于XC800系列单片机的通用LIN从节点驱动程序,有详细注释和可更改参数的配置文件 -XC800 MCU series based on the generic driver LIN slave nodes, with detailed comments and can change the configuration file parameters
SCI
- 用于TMS320F2812配置SCI通讯的源程序。-TMS320F2812 configuration for the source SCI communications.
AN101SW_IO
- C8051f020单片机AN101SW配置端口IO交叉开关译码器-C8051f020 single-chip IO port configuration AN101SW cross-switch decoder
COS-II
- UC/OS-II内核详细解释,并对安装配置环境进行说明。很实用-UC/OS-II
SAM7S-WDT
- 介绍AT91SAM7S256 USB HID 的基本用法。 AT91SAM7S256开发板配置成普通双键鼠标。-use of AT91SAM7S256 USB HID fit AT91SAM7S256 into mouse
ccs_cmd
- cmd 文件用于DSP 代码的定位。由于DSP 的编译器的编译结果是未定位的, DSP没有操作系统来定位执行代码,每个客户设计的DSP 系统的配置也不尽相同,因此需要用 户自己定义代码的安装位置。安装位置是指,编译完成的代码是存放在dsp的那个位置,程序空间RAM或者数据空间RAM,起始地址以及长度。-cmd file for the positioning of DSP code. As the DSP of the compiler to compile the result
AD12
- TI官方MSP430x13x, F14x, F15x, F16x系列单片机AD12配置程序-TI Official MSP430x13x, F14x, F15x, F16x series of single-chip configuration procedures AD12
h_jtagjietu_sjf
- h-jtag端口设置截图+sjf源码,用于解决电脑主板没有并口,无法接仿真器的情况(须买pci转并口卡),若使用h-jtag则依图设置可以检测到arm核,按配置改sjf源码可以正常烧写芯片-h-jtag port settings screenshot+ sjf source for the settlement of a computer motherboard there is no parallel port, emulator can not accept the situation (
DSPSRC
- Audiocfg_FIR--利用dsp6713实现fir滤波 Audiocfg_IIR--利用dsp6713实现iir滤波 fileout--烧写flash必要的准备 SDRAM--6713读写SDRAM simfft--6713实现fft变换 sstpro--烧写flash Timer_GPIO--通过定时器实现led灯周期闪动 Videocfg--视频配置-Audiocfg_FIR- the use of fir filter dsp6713 ach
keyboard
- mega16控制的矩阵键盘驱动,配置1602液晶显示,经调试过能用-matrixkeyboard
RTL8139end_vxworks_config(P4)
- RTL8139网卡的驱动文件(p4)及其在vxworks下的配置方法。-RTL8139 network adapter driver files (p4) and its configuration under vxworks.
libminigui-1.6.0-linux-host
- 这是在Linux下进行GUI界面开发的全套libminigui软件包。我里面写了一个安装步骤的文档,希望对需要的朋友有用。提醒一下,如果是做移植的话,在进行libminigui的./configure配置和安装reg-host完了以后,还需要回过去把libminigui再重新进行./build....-TFT(中间还有命令),这样就可以把原先的lib库进行一次交叉编译了,在做移植的时候就不会有错误情况出现了。-This is a GUI in Linux under the full set o
UCOS-II
- 基于FPGA的实验 UC\OS-II操作系统移植,使用SOPC软件及其配置方法,掌握其在NIOS II IDE 中的简单使用。-FPGA-based experimental UC \ OS-II operating system migration, the use of SOPC software and its configuration to grasp the NIOS II IDE in the simple use.
PS2-SPI
- 使用SOPC软件及其配置方法,以高速12位串行AD7920实现0-3.3V的ADC转换。 PS2控制器接口模块,把键盘数据通过串口发送到电脑主机上显示哪个键被按下。-Configuration software and its use SOPC approach to high-speed 12-bit serial AD7920 to achieve 0-3.3V the ADC conversion. PS2 controller interface module, the keyboa
LCDdriverbasedonS3C2410
- 该源码是基于ARM9 S3C2410A的LCD移植程序,LCD选用的是Sharp LQ080V3DG01 ,源码主要对LCD进行设置、初始化、并对LINUX kernel内核进行配置-。
8bitpwm
- 参考程序B:WPCA1pwm8.C 程序实现PCA模块0和1的8位PWM输出J涑鼋臗EX0配置在P0.0脚输出方波占空比为2/3
Connguration_and_Coding_of_Cache_in_VxWorks_operat
- 摘要:该文提出了一种合理地应用Cache的方法,以解决VxWorks环境下操作系统的启动速 度慢和应用程序运行效率低的问题。在启动过程中,通过修改配置文件来合理地打开代码 Cache和数据Cache,加快操作系统的启动速度;在应用程序开发过程中,通过使用不同的Cache 编程方法,提高应用程序的运行效率。实例分析给出了具体应用的实现方法。 关键词:VxWorks操作系统;高速缓冲存储器;直接存储器存取-Abstract: This paper presents a reasona