搜索资源列表
MyJTAGForAvr
- eeprom和flash是自制JTAG的源程序，熔丝配置位图为写MG16时的熔丝配置情况。 -EEPROM and flash is a self-made JTAG source, Fuse-allocation map was made MG16 the Fuse configurations.
uCOS_II_ARMulate
- uC/OS-II操作系统在ADS-ARMulator上的移植。uC/OS-II就不用我介绍了，想必很多人都很感兴趣。但没有硬件平台调试，而skyeye初学者又很难上手怎么办？该移植可以运行在ADS的AXD调试器的ARM模拟器上，相对而言容易配置，大大方便初学者的上手，使更多的人容易进入嵌入式开发殿堂。在ADS1.2环境下编译运行。-uC / OS-II operating system ADS-ARMulator the transplant. UC / OS-II would not have
fdpll
- 简单的可配置dpll的VHDL代码。 用于时钟恢复后的相位抖动的滤波有很好的效果， 而且可以参数化配置pll的级数。-simple configurable dpll VHDL code. Clock Recovery for the jitter filtering is a very good result, but can pll configuration parameters of the series.
TMS320LF240xDSPc
- 这是ti公司2000系列dsp的,应用系统及其端口配置的的程序,用c语言编写的.以word格式给出.很有用的.-This is the company's 2000 Series DSP, application systems and port configuration procedures, c language used in the preparation. word format to give. very useful.
SCIB_RS232
- TMSC320F2812串口SCI通信,SCIA,SCIB,波特率设置，寄存器配置-TMSC320F2812 serial communications, SCIA, SCIB, baud rate settings, Register Configuration
S3C2410init
- 2410处理器bootloader,的初试化配置和 系统调用的寄存器配置函数-2410 processor, the buds of configuration and system configuration register called Function
ov511-1.63
- 是一个linux下的摄像头驱动,网上的驱动源码比较难找,这个基本能用,根据具体的摄像头配置和设置改下,linux下可编译-the camera driver, online source quite difficult to drive, the basic used. specific camera configuration and setup changed, the compiler under Linux
lcd_an_src
- 瑞萨单片机LCD控制，可以对多种液晶进行控制，可配置。-Renesas MCU LCD control, for a variety of LCD control that can be configured.
Example Ethernet Software for SCC1
- MPC860的SCC1配置以太网示例代码-MPC860 SCC1 configuration Ethernet sample code
Example HDLC Software for SCC2
- MPC860的SCC2配置HDLC示例代码-MPC860 SCC2 configuration HDLC sample code
Example I2C Software (Using Microcode to Relocate
- MPC860的配置I2C示例代码-MPC860 configuration I2C sample code
config
- 用单片机配置FPGA，英文，不用说了吧，呵呵，快下吧-MCU FPGA configuration, English, needless to say, all right, what are you fast
minigui_install
- minigui安装配置（red7.x以上版本）-MiniGUI installation configurations (red7.x versions)
testomap
- TI OMAP5910(1510)的最简单测试程序,用于 硬件最初的调试,简要文档含环境配置-TI OMAP5910 (1510), the most simple test procedure for the initial hardware debugging, summary documents containing environment configuration
LPC915-I2C-MASTER
- LPC915的I2C模块配置为主机时的接口程序，可直接添加到工程里使用-LPC915 I2C module configuration for the host interface can be directly added to the used in the project
LPC915-I2C-SLAVE
- LPC915的I2C模块配置为从机时的接口程序 可直接添加到工程里使用-LPC915 I2C module configuration from the plane at the interface can be directly added to the used in the project
VxworksTrainingDocument
- 本文档对实时操作系统作了简要介绍，并针对VxWorks系统的特点进行了具体的说明和分析，从VxWorks系统的任务管理、通信机制、系统配置、系统接口几个方面展开。-the right real-time operating system files were briefed, against VxWorks system and the characteristics of the specific descr iption and analysis, VxWorks system from t
xapp290
- 从Xilinx网站上下的，学习FPGA部分动态重配置很好的例子。-from across the Xilinx website, learning some FPGA dynamic reconfigurable good example.
bios-lt75.tar
- 这是bios-lt的最新板，(1) bios.img占用的扇区数由4个合并为2个,相应的文件大小由193K减小为66K (2) 实现了对FLASH芯片BOOT扇区的处理,建立FLASH分区时不用再考虑让开BOOT扇区 改动的主要目的是想做到: 在29F040上空出384K的空间,建立一个分区存放不含应用程序的uClinux kernel, 将29LV160作为一个大分区,在其上建立JFFS2文件系统,并挂接为uClinux的根文件系统. 系统应用程序全部存储在
pciconfig
- 一个读取PCI配置空间的TOOL (在DOS下OR WIN 98)-a reading of the PCI configuration space TOOL (DOS OR WIN 98)