搜索资源列表
Project
- Design a sequential circuit that has two inputs w1 and w2 and an output z. A clock and a reset signal are also present. Its function is to compare the input sequences on the two inputs. If w1 ≠ w2 during any two consecutive clock cycles, the ci
ADXL345
- IIC总线读取传感器的X,Y,Z三维加速度值，极大的方便与平衡机器人，状态保持，状态转移等设计开发。-IIC bus read sensor X, Y, Z three-dimensional acceleration value, great convenience and balancing robot, the state maintained, the state transition and other design and development.
6050
- 基于STC51单片机和MPU6050的程序，可以显示速度，加速度，和X,Y,Z坐标。通过LCD12864（串行）显示。-The code can display the speed ,Acceleration, x,y,z coordinate and so on/
usb-device-massstorage-project-at91sam7x-ek-iar.z
- When an EK running this program connected to a host (PC for example), with USB cable, the EK appears as a USB Disk for the host. Then the host can format/read/write on the disk. If there is SDRAM on the EK, the disk can be up to 10M so that read/wr
adxl345
- 角度模块实现x.y.z.三轴扫描，应用在51单片机上-Xyz-axis scanning angle module, used in the 51 SCM
Intro_to_Digital_Design-Digilent-Verilog_Online.z
- Nice Book for Verilog Basics
MPU6050
- 六轴 陀螺仪MPU6050 测试代码.X Y Z ＲＸ ＲＺ ＲＹ -MPU6050 demo
ps2
- 用verilog语言编写的PS2键盘程序，按下相应的A-Z字母按键后，会将相应的字母通过串口发送-Using verilog language PS2 keyboard program, press the corresponding letter keys AZ, the corresponding letter will be sent through the serial port
zwave.tar
- Z-way communication protocol
C8051F-WAV
- 利用C8051F的SPI接口的速度读取SD卡中的数据。进而利用片上的DA解码之。由于是电流型DA，用电阻得到电压。为了防止后置高阻抗干扰，因此。做了简单的电压跟随。最后滤掉直流-Use C8051F speed SPI interface to read the data on the SD card. Furthermore the use of DA decoding chip. Because it is current-DA, with resistance to get voltage
myczt
- 用Verilog HDL语言对chirp Z变化进行实现，并附带测试文件。-Using Verilog HDL realize changes for chirp Z, and come with a test file.
Z-video-udp-sender
- 在基于OK6410开发板上读取OV9650摄像头视频照片，源程序采用QT开发，并利用UDP协议将视频通过网络发送到PC机上-OK6410 development board based on reading the OV9650 camera video photos, source code using QT to develop and use UDP protocol to send the video to the PC through a network
Z-video-udp-receiver
- 在LINUX系统下，采用UDP协议，读取从网络传送过来的视频图片，并动态的显示在QT开发的界面上-Under LINUX system, using the UDP protocol, transferred from the network to read over the video picture, and dynamically displayed on the QT interface development
ComparatorTestVersion
- 基於wire方式設計的補償器,但需外接DFF依照同學想做幾階的可在進行外加,Z^-1 需2個 Z^-2 3個依此類推.僅提供實做參考,實際參數需自行設計-Based on wire mode compensator design, but need to add DFF in accordance with the order of a few students want to be carrying plus, Z ^-1 need two Z ^-2 3 one, and so on. Pr
Example-b8-5
- 四态的VCD文件，参数在0/1/X/Z之间变化，没有信号的强度信息-The four state VCD file, parameter changes between 0/1/X/Z, no intensity information of the signal
GY-50Test-procedures
- GY-50三轴陀螺仪GY-50-SCH、GY-50-L3G4200资料，GY-50测试程序-关闭翻译英语中文德语检测语言 中文(简体)英语日语 翻译文字或网页 GY-50三轴陀螺仪GY-50-SCH、GY-50-L3G4200资料，GY-50测试程序 请键入文字或网站地址，或者上传文档。 取消 GY-50 sān zhóu tuóluó yí GY-50-SCH,GY-50-L3G4200 zīliào,GY-50 cèshì chéngxùGY-50 three-
GenericApp--Zstack_UART
- CC-2530 的 Z-stack 串口应用-Z-stack UART application of CC-2530
ADXL345_Z_out
- 三轴加速度传感器模块GY-29 ADXL345的IIC测试程序，z轴输出的调试程序 使用单片机STC89C51 晶振：11.0592M 显示：LCD1602-Triaxial accelerometer module GY-29 ADXL345 the IIC test program, the debugger uses the microcontroller output z axis STC89C51 Crystal: 11.0592M display: LCD1602
ilg.gnuarmeclipse.repository-2.4.2-201411261616.z
- ilg.gnuarmeclipse.repository-2.4.2-201411261616 gcC COMPILER 2014 VERSION
HTG128128Z-SSD1814-P80-Ver1.2
- HTG128 Z，128*128液晶驱动程序，程序经过测试，正常使用。-HTG128128Z, 128*128 LCD driver, the program after testing, normal use.