搜索资源列表
TBA-8246C
- 用c语言编写的单片机程序,能够实现多串口通信及485通信,提供给大家分享。-c language used in the preparation of SCM procedures can achieve multi-485 serial communications and communications, to share with you all.
485system
- 工业控制及测量领域较为常用的网络之一RS-485。本例通过485总线实现主从机之间的通信、数据传输及控制。程序是用C语言实现。内有详细解释,可读性和移植性强。-industrial control and measurement field is one of the commonly used network RS-485. 485 cases through the realization of the main bus from the plane between the communic
RS-485
- 单片机智能产品c语言设计实例详解程序,希望能对大家有用!
C51bus
- 51单片机的各种接口总线程序包,采用C语言编写,包括51的串口通信,485通信,I2C程序,SPI程序,1WIRE程序等多种接口的程序包可谓一网打尽。
master
- 基于AVR平台的C语言开发,Atmanavr环境下编译实现,该源程序包括用mega16的UART口实现在片485通讯。
minge7
- 一个用C语言控制的读写7022,存储数据,485上传数据,向液晶模块显示数据的程序。此程序为测试程序,所有与模块通讯功能都能实现。
Src
- 电力仪器仪表程序!多功能液晶表三相三线,三相四线,485,232,-Power Instrument program! Multi-phase three-line LCD table, three-phase four-wire, 485,232,
CAN
- CAN51开发板功能 1、 USB或DC+5V供电; 2、 89c52+sja1000+tja1050(tja1040)(p82c250);89c52+mcp2515+tja1050(tja1040)(p82c250);通过跳键选择sja1000或 mcp2515,用户任选一种CAN控制芯片; 3、 支持RS232/422/485总线与CAN总线相互转换; 4、 CAN总线波特率可调:20,40,50,80,100,125,200,250,400,500
485
- 这是个485程序!可以直接与电表的485接口连接进行采集电表的数据!!是一个很不错的程序-This is a 485 program! Directly with the 485 meter connection meter data collection! ! Is a very good program
SourceCode21_SCI485
- fm2812下485口范例程序,C语言编写-fm2812 under 485 examples of the procedure, C language
SCI
- dsp2407 SCI 程序 c语言-c language program dsp2407 SCI
rs485_2
- 51单片机 485双机通信程序 用c语言编写 keil编译环境-51 SCM 485 pairs of machine communication program using c language keil build environment
485FULLDUcomm
- 本程序是C语言基础的单片机程序,实现485串行口的全双工通信。是学习单片机串口通信的好程序。运行成功。-This program is a C language-based microcontroller program to achieve 485 serial port full-duplex communication. Microcontroller serial communication to learn a good program. Run successfully.
DSP.2812.SCI
- DSP2812的C语言例程:SCI。自己编的,上机运行好,希望大家能用-DSP2812 C-language routine: SCI. Compiled their own, on the machine running well, hope everyone can be
51_485
- 485通讯程序 C51单片机 采用C语言开发-485 C51 microcontroller program development using C language
485Mon
- 51单片机C语言程序设计实例精讲 第28章 单片机实现RS-485总线现场监测系统-51 Microcontroller C Programming Language Example Jingjiang Chapter 28 RS-485 bus, MCU-site monitoring system
RS-485
- 单片机点对多点通讯程序C语言,用途非常广泛-MCU-multipoint communication program C language, uses a wide range of
485
- freesclae DZ60 485 C语言通信源程序-freesclae 485 communications program
485
- RS4855串口通信试验(接受与发送),c语言源程序-RS4855 serial communication test (acceptance sent), c language source
多合一code
- 采用51单片机作为主控制器,通讯方式为485总线,通讯协议为Modbus,波特率为9600,8位数据,1个停止位,无校验位; 本程序作为从机部分编写的;(Using 51 single-chip microcomputer as the main controller, communication mode is 485 bus, communication protocol is Modbus, baud rate is 9600, 8 bit data, 1 stop bits, no pa