搜索资源列表
modbus.rar
- modbus485通信协议C程序，经修改已用于项目，熟悉后修改部分参数即可用于485通信相关项目。,modbus485 communication protocol C program, as amended, have been used for the project are familiar with some parameters after the change can be used for 485 telecommunications related projects.
modbus.rar
- 51 modbus源代码，rtu 格式,在c8051f120上实现,51 modbus code ,rtu mode
modbus 单片机从机的软件
- modbus rtu 485 通讯协议 的编写，单片机从机的软件，，已经可以了，调试通过了，-modbus rtu 485 communication protocol preparation, single-chip from the machine' s software, they can already, and debugging through,
ModBus_rs485_send
- 基于dspic33f单片机，RS485硬件的ModBus通讯协议程序，初始状态为发送-Based on dspic33f microcontroller, RS485 ModBus communication protocol program the hardware, the initial state to send
RS485_mega16
- RS485多机通信（主机呼叫从机，从机返回数据） 基于AVR mega16单片机，实现RS485通信，内含proteus仿真图。-More than 485 machine communication (calls from the host machine, from machine to return data) based on AVR mega16 single chip to achieve RS485 communications, containing proteus simu
8051F410_AD_MODBUS
- 本文件是通过485通讯将接受MODBUS指令，采集AD数据，发送出并在对应的LED数码管上十六进制循环显示。-This document will be accepted by 485 MODBUS commands AD data collection, sending out and the corresponding LED digital display on the loop hex.
ModbusMaster
- ModbusMaster.h - Arduino library for communicating with Modbus slaves over RS232/485 (via RTU protocol). This file is part of ModbusMaster. ModbusMaster is free software: you can redistribute it and/or modify it under the terms o
Modbus
- 51单片机modbus协议基于485接口-51 MCU modbus program based on 485 interface
modbusRTU_C51_RS485
- modbus RTU 的C51程序 单片机89S52 通信波特率 9600 8位数据 1位停止位 偶校验 485通位接口 单片机控制板地址 localAddr(变量) 通信可设置数据的地址： 字地址 0 - 255 (只取16位的低8位) 位地址 0 - 255 (只取16位的低8位)-modbus RTU' s C51 program microcontroller 89S52 Communication baud rate 96008 bits of d
chfV1_21
- chf MODBUS通讯协议 ,485发送格式,以及协议构成-chf MODBUS communication protocol, 485 sending format, as well as the agreement constitutes a
modbus149U0(500)
- MSP430 485程序,搭上硬件直接用-MSP430 485 program, to catch the direct use of the hardware
串行口通信程序
- 基于modbus协议的上位机和单片机串行通信的程序(serial communication between PC and microcontroller program based on Modbus protocol)
实验3 MODBUS 485串口1
- MODBUS串口3实现串口通讯，稳定性高，架构简单。(MODBUS serial port 3 to achieve serial communication, high stability, simple architecture.)
V4-RS485 MODBUS从站例程(V1.0)
- 基于STM32F103的RS485 MODBUS从站例程(RS485 MODBUS Slave Slave routine based on STM32F103)
ModBus-Master
- 基于单片机STM32的modbus协议，采用485总线(The Modbus protocol based on single chip microcomputer STM32 adopts 485 bus)
UCOSII_MODBUSRTU_usart3-485
- ucos-ii的freemodbus移植串口3 485(Freemodbus porting serial port 3485 of uCOS-II)
MODBUS- 485SLAVER
- 本例程为 RS485 MODBUS 主站例程。可以通过按键发送相应的 MODBUS 命令，然后等待从站应答 （或超时）退出等待。 程序使用串口 3（ USART1）与从机通讯，执行结果通过串口 1（ USART1）送到计算机的串口。可以 通过 PC 机的串口终端软件观察程序执行结果(This routine is the RS485 MODBUS master station routine. You can send the corresponding MODBUS commands t
modbus
- 在stm32f103zet6下的485总线通讯加modbus协议(485 bus communication and Modbus protocol under stm32f103zet6)
MODBUS 仿真_Proteus_51
- 51单片机多机modbus 主从通讯程序 Proteus仿真串口485。(51 microcontroller multimachine modbus main from the communication program procus simulation serial port 485.)
stm32f103+rs485+modbus+freertos
- 在freertos操作系统下采用modbus协议进行rs485通讯(485 communication using Modbus protocol under FreeRTOS operating system)