搜索资源列表
8段数码管
- 8段数码管的源代码-eight digital control of the source code
8js
- 51单片机0-999 秒计时 8数码管显示 asm/c双语言编写 -51 seconds time SCM 0-999999 8 asm2 Digital Display / c-language
arm 8段数码管
- 用hitool开发的8段数码管的显示程序 c语言的程序 嵌入一点汇编-hitool development with eight of the digital display control procedures c procedural language embedded 1:00 compilation
chuankou1-8
- 简单的八位数码管显示,用了8片74LS164,将串型数据变为并行
八个数码管(用138,47)
- 用8个数码管,用一片48和一片138控制 的子程序,-with eight digital control with a 48 and a control subroutine 138,
6位8段数码管显示-程序
- 用汇编语言编写的6位8段数码管显示程序与MS-51单片机实验系统配合使用-assembly language prepared by six of eight digital control display program with the MS-51 used in conjunction with experimental system
8位计算器汇编程序
- 基于XL1000开发板编写的8位计算器,包括键盘扫描和数码管显示
ATMEGA16_8LED.rar
- AVR单片机来驱动8位数码管,用74HC595来做驱动段和位的驱动芯片,AVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR 74HC595 LEDAVR
ADC0832.rar
- ADC0832 端口复用 8数码管显示 初学ADC及单片机的助手 有 proteus 仿真电路,ADC0832-port multiplexing 8 digital tube display beginners ADC and the microcontroller' s aides have proteus simulation circuit
简单的8位AD采样
- 简单的8位AD采样,转化为数码管显示,本程序主要是教会初学者使用AD,高位AD需要自己开发,Simple 8-bit AD sampling, into a digital display, the program is for beginners to use the Church AD, a high need to develop AD
基于MAX7219的8位数码管显示
- 第5章 基于MAX7219的8位数码管显示 主要针对初学者的源程序,是数码管编程入门的好帮手。-Chapter 5, based on MAX7219 8-bit digital display the main source for beginners, digital program entry is a good helper.
CHENGKONGLVBO
- C51程控滤波程序,采用MAX262,和数字电位器,采用8位数码管显示,按键是4*4按键,主要是受到开发条件的限制,使用的是开发板-C51 program-controlled filtering procedure for the MAX262, and digital potentiometers, using eight digital tube display, button is 4* 4 buttons, mainly due to the development of condit
8个数码管显示数码管动态扫描显示
- 共阳极数码管显示1,2,3,4,5,6,7,8。FPGA可直接编译。
27-12个IO驱动8个共阴共阳数码管
- 通过单片机模拟数码管驱动,驱动数码管,节省成本(Analog digital drive through the microcontroller, drive digital tube, saving costs)
74HC595驱动8个数码管
- stm32f103 74HC595驱动8个数码管(74HC595 drives 8 digital tubes)
八位数码管
- 这是在keil环境编译下的STMF4驱动595八位数码管的源代码程序(This is the source code program for STMF4 that drives 595 8-bit digital tubes under the keil environment)
74HC595八个数码管动态显示
- 用PROTEUS仿真arduino实现74HC595驱动8个数码管的项目文件,含原理图、源代码,仿真实现的全套资料。(PROTEUS simulation using Arduino to achieve 74HC595 drive 8 digital tube project files, including schematics, source code, simulation of the full set of information.)
89C51按键控制数码管
- 用89c51单片机实现独立的按键控制8位数码管的显示(Button control digital display with 51 single chip microcomputer)
实验十六 矩阵按键数码管存储
- 按下按键后,经过51单片机处理后,显示在8个数码管上,并且存储。(After pressing the button, after 51 single chip processing, it is displayed on the 8 digital tubes and stored.)
8人抢答器
- 基于AT89C51单片机设计制作一个抢答器,具体要求如下: 1、 设计一个智力竞赛抢答器,可同时共8名选手参加比赛,编号为1、2、3、4、5、6、7、8,各用一个按键。 2、 用一个按键作为主持人总开关,用来控制系统的清零和抢答的开始。 3、 抢答器开始后,数码管开始10秒倒计时,若有选手按动抢答按钮,在LED数码管上显示选手的编号,同时灯亮且伴随声音提示;倒计时完成后,选手不能在抢答;有人抢答成功后,要禁止其他选手抢答;最先抢答选手的编号一直保留到主持人将系统清零。(Based on A