搜索资源列表
xiaoche
- 以L298为电机驱动,以光电开关为传感器,控制小车循迹-L298N motor drive, to the photoelectric switch sensor, control car tracking
bujindianji
- 实现51单片机控制步进电机的转动,驱动模块使用的是L298N-51 single-chip control stepper motor rotation, the drive module is L298N
car
- wifi robot 智能车51代码 l298n和步进电机-wifi robot code
L298-driver
- L298N详细驱动电路,有助于单片机开发者更好的设计电路图。-L298N drive circuit, contribute to the single-chip developers to better design the circuit diagram.
xunjixiaoc
- 自动循迹小车控制器采用STC89C52单片机,采用LCD1602液晶显示屏显示当前小车速度和里程等数据;电机正反转采用L298N集成电路模块来驱动,也可以直接采用三极管组成桥式驱动电路来控制。里程检测传感器采用霍尔传感器或光电发射接收对管。-Automatic tracking car controller with STC89C52 SCM LCD1602 LCD display shows the current car speed and mileage data motor rever
8.2zhi_neng_xiao_ce
- keil写的一个智能小车程序,采用AT89S52芯片,黑色轨迹探测传感器采用RPR220光电对管,两个直流电机的驱动采用ST的L298N电机驱动芯片-the keil write a smart car program AT89S52 chip, black trace detection sensor using RPR220 photoelectric tube, two DC motor drivers using ST L298N Motor Driver IC
motor
- 直流电机的控制,利用L298N驱动直流电机,控制转速的大小停止等-DC motor control, L298N drive DC motor, speed control the size of the stop
car
- 基于51单片机的循迹小车的部分程序代码,驱动器l298n,四驱-51 microcontroller tracking car-based program code
Msp430g2553-control-of-the-car
- 基于msp430g2553的小车控制,实现方向控制,驱动芯片为L298n-Msp430g2553 control of the car, direction control, and driver chips for L298n
qianj
- L298N使用 小车前进程序小车前进程序-L298N car forward
L298
- 常用直流电机驱动芯片资料汇总 L298N-Common DC motor driver chip data aggregation L298N
main.rar
- 51单片机通过PWM控制直流电机的驱动,L298N 驱动芯片,可以通过串口,用上位机来控制,控制直流电机的正反转,加速减速,PWM control DC motor driver L298N 51MCU through the serial port, using the host computer to control, control of a DC motor reversing, acceleration and deceleration
motor
- AVR使用硬件PWM驱动L298N来控制电机,PWM频率为2K-AVR hardware PWM driver L298N to control the motor, PWM frequency for 2K
L298N-DC-motor-PI
- 基于单片机PI控制直流电机的自动调速系统,包含程序,适合广大的学习者。-Based on single-chip PI control of DC motor speed control system, including procedures for the majority of learners.
Step-Motor-MSP430
- 用msp430G2553 控制两相四线的步进电机(通过L298n),带正反转控制,可控制前进距离和顺/逆时针转动角度。-control the step motor with msp430G2553,including CW/CCW, whoes angle is adjustable.
StepMotor_DSP
- 自己用的TMS320F28335 写的简单的控制两相步进电机的程序(通过L298n),半步模式。可直接输入电机前进距离,顺/逆时针转动的角度。-TMS320F28335 control the two-phase step motor, half-step.
CHECK
- 本迷宫小汽车选用8位STC90C52单片机为控制器,通过3个红外光电传感器E18-D80nk对信号进行采集,采集到的信号经串口转换MAX232CPE处理后传给STC90C52单片机,经单片机处理后,发出控制命令给L298N,驱动2台直流电动机进行相应的动作。该小车实现了前进、后退、左右转弯、避障以及显示运行时间等基本功能,整个系统结构简单,可靠性高,实验测试结果满足要求-STC90C52 microcontroller pass the maze of car use 8 STC90C52 si
51mcudriveL298N
- 51单片机驱动电机正反转(需要L298N驱动板)-An program for MCS51 MCU to drive a L298N motor diver
L298N_Drv2.5a2.6
- l298n控制步进电机两相八拍测试程序,加加加几-l298n controlled stepper motor test program
L298Nmodule
- L298N 电机驱动 资料 简单明了 -The L298N motor drives data