搜索资源列表
USART_ADC12
- MSP430F149串口行实验程序 //使用ADC12采集实验,将采集到数据送向PC.(序列单次采集,采用定时器A作为时钟源) //P3.4为发送,P3.5为接收 晶体使32768HZ/8MHZ. 串行波特率B/S //使用SMCLK作为波特率发器时,不能使用LPM2,LPM3!
LT_1B_msp430_LPM3
- LT_1B msp430开发板例子程序－LPM3
LPM3
- Low power modes in MSP
LPM3
- msp430学习资料，其中包含原理图及重要注释，也有配套的源码说明.低功耗模式3-msp430 learning materials, including schematics and important notes, also have matching source descr iption.Lmp3
LPM3
- msp430进入LMP3休眠模式，每4秒点亮LED灯-his program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system. All I/O configured as low outputs to eliminate floating inputs. Current consumption does increase wh
LPM3
- 这是msp430低功耗的基础程序，请大家下载，对你们的学习很有帮助。-This is a low power msp430 based program, please download, on your very helpful.
41695046MSP430F149_UART
- MSP430F149串口通信程序,串口接收中断,退出LPM3模式.-MSP430F149 Serial Communication Program, receiving the serial port interrupt, quit LPM3 mode.
LPM3
- MSP430F149系列 LM3使用代码-MSP430F149 series LM3 use code
MSP430-application-of-thermometer
- 在《温度计_基本原理》程序中，已经实现了一个温度测量和显示的系统，但因为采样速率很快，且对基准源不加控制，耗电很大(800uA左右)。本例中，将温度采集速度降到1秒一次，且采样间隙时间不仅关闭基准源，还让CPU进入LPM3休眠状态，大大节省了耗电。该程序功耗仅10uA左右，可用纽扣电池长期运行(2年)。实际上对于环境温度1秒1次采样仍属浪费，如果降到5秒一次，功耗可下降到4uA左右(CR2032电池工作5年)。按KEY3后，CPU进入LPM4，功耗下降到0.1uA，这是一种常用的不断电的关机方法
fet140_uart07_09600
- MSP430串口0通信。波特率9600，回显收到的8个字符。具有参考价值-his program demonstrates a full-duplex 9600-baud UART using USART0 and a 32kHz crystal. The program will wait in LPM3, and receive a string[8] and echo back the complete string.
LSD-RF4619-CS01-t
- 基于MSP430FG4612的CC1101无线通信程序，发送端：2s的唤醒帧(无数据包)，延时20ms，数据发送一个14字节的数据包（若加上第一个len字节则整个包为15字节），其中第5个字节每发一次累加，延时1S。重复此过程；接收端：默认为CS RSSI，接受数据，并将第5个数据显示在LCD上。在接收端开1S的定时，若无数据包，则转为LPM3。-Based on the MSP430FG4612 CC1101 wireless communication program, the sender
msp430x20x3_lpm3
- MSP430F20xx Basic Clock, LPM3 Using WDT ISR 低功耗模式3-MSP430F20xx Demo- Basic Clock, LPM3 Using WDT ISR
LPM3
- MSP430进入低功耗的源代码、值得借鉴-MAP430 for LPM3
MSP430-uart
- 430 UART程序实例 包括初始化代码设置，中断方法实现-Descr iption: This program demonstrates a half-duplex 2400-baud UART using Timer_A3 and a 32kHz crystal. The program will wait in LPM3, echoing back a received character using 8N1 protocal. The 32768 cryst
LPM3
- Msp430F149 LPM3例程，测试通过，完美无BUG-Msp430F149 LPM3 routines, tested, Perfect BUG
ds18b20_msp430F149
- 用MSP430F149单片机采集11路DS18B20级串口0和串口1的使用及定时器唤醒 LPM3睡眠模式-11 Road with MSP430F149 MCU DS18B20 collection level serial port 0 and 1, and the use of sleep mode timer wake LPM3
LaunchPad-LPM3
- LaunchPad LPM3 MSP430G2553
msp430g2xx3_lpm3
- 这个软件另MSP430正常地工作在低功耗模式3，令P1.0以4秒的间隔闪烁。-This program operates MSP430 normally in LPM3, pulsing P1.0 at 4 second intervals. WDT ISR used to wake-up system. All I/O configured as low outputs to eliminate loating inputs. Current consumption does increa
LPM3
- msp430F149,说明：此程序运行在LPM3 MSP430通常在4秒的时间间隔，脉冲P3.4。 WDT ISR用来唤醒系统。- Descr iption: This program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system.
UART9600
- msp430F149,说明：回声一个接收到的字符，RX ISR使用。在主循环UART0准备接收一个字符中断活跃。主循环等待LPM3。UART0的ISR部队主循环后退出LPM3接收回波接收到的字符一个字符。-Descr iption: Echo a received character, RX ISR used. In the Mainloop UART0 is made ready to receive one character with interrupt active. The Mainl