搜索资源列表
stc
- 单片机51头文件，其中定义了P4端口。当使用P4引脚时可直接此头文件。-SCM 51 header file, which defines the P4 port. when using the P4 pin can be directly this header file.
STC89C51RC_RD_HEAD
- STC89C51RC_RD_HEAD是STC芯片的头文件,包含此头文件后可以免去再次定义端口引脚.-STC chip STC89C51RC_RD_HEAD is the first document, including this header file can be removed from the re-definition of the port pin.
MCP2515_driver_s3c2440based
- 本驱动程序在s3c2440上实现了两路基于SPI的CAN总线控制器。两通道可以并行，并使用外部定义的两个信号量来通知接收任务收到CAN总线帧，并将其存入预先定义的队列中（帧定义在CAN总线控制器驱动程序的头文件中）。CAN总线控制器的中断引脚分别连接到ARM的EINT3和EINT8_23上-The driver s3c2440 achieved a two-way SPI-based CAN bus controller. Two channels can be parallel, and us
lcd_h
- This the header file to drive a LCD using only 6 pin of the microcontroller.- This is the header file to drive a LCD using only 6 pin of the microcontroller.
flash_card_20090915094630
- Six pin header output SPI memory chip placed on a small board includes all SPI signal
AVR_micro-cheat-sheet.png
- pinouts of ATtiny25/45/85, ISP Header 6-pin/10pin, ATtiny2313, ATmega48/88/168/328 Arduino, FTDI Cable
AT90usb
- AT88SC0808函数库,包括底层库，引脚定义可修改。应用层库以.a的形式给的，提供了应用头文件-AT88SC0808 library, including the underlying database, pin definitions can be modified. Library to the application layer. A form given to provide the application header files
sd2068_avr
- sd2068应用，包括头文件、引脚说明，及其控制等方面-sd2068 applications, including header files, pin descr iptions, and control, etc.
74HC595
- 74HC595 C51驱动代码，以头文件和源文件的方式给出，带中文注释，应用时直接包含，并修改头文件中的引脚定义即可。-The 74HC595 C51 driver code, header files and source files given application directly with the Chinese Notes and pin definitions can modify the header file.
STM32F100RB_sch
- STM32F100RB microcontroller, 128 KB Flash, 8 KB RAM in 64-pin LQFP On-board ST-Link with selection mode switch to use the kit as a stand-alone ST-Link (with SWD connector) Designed to be powered by USB or an external supply of 5 V or 3.3 V C
ADC0832
- 芯片ADC0832 C语言驱动源程序，内含头文件和C程序，可经修改头文件管脚定义直接驱动使用-The chip ADC0832 C language driver source code, contains header files and C program, you can use direct drive pin definitions revised header files
DS1302
- 芯片DS1302 C语言驱动源程序，内含头文件和C程序，可经修改头文件管脚定义直接驱动使用-The chip DS1302 C language driver source code, contains header files and C program, you can use direct drive pin definitions revised header files
LCD1602
- 液晶LCD1602 C语言驱动源程序，内含头文件和C程序，可经修改头文件管脚定义直接驱动使用-LCD1602 C language driver source code, including header files and C programs can directly drive pin definitions revised header files
X5045
- 芯片X5045 C语言驱动源程序，内含头文件和C程序，可经修改头文件管脚定义直接驱动使用-Chip X5045 C language driver source code, including header files and C programs, direct drive pin definitions revised header files
msp430HG2231
- MSP430-HG2231 is header board with MSP430G2231IPW14R ultralowpower mixed signal microcontroller from Texas Instruments. MSP430G2231IPW14R has a built-in 16-bit timer, ten I/O pins, a 10-bit A/D converter and built-in communication capability us
sd2068_avr
- sd2068应用，包括头文件、引脚说明，及其控制等方面-sd2068 applications, including header files, pin descr iptions, and control, etc.
51nrf905
- nRF905 是挪威 Nordic VLSI 公司推出的单片射频收发器，工作电压为 1.9 ～3.6V， 32 引脚 QFN 封装 (5×5mm)，工作于 433/868/915MHz 三个 ISM(工业、科学和医学)频道，频道之间的转换时间小于 650us。 nRF905 由频率合成器、接收解调器、功率放大器、晶体振荡器和调制器组成，不需外加声表滤波器， ShockBurstTM 工作模式，自动处理字头和 CRC(循环冗余码校验)，使用 SPI 接口与微控制器通信，配置非 常方便。此外，
I2C
- 软件模拟IIC驱动程序，秩序修改i2c.h头文件IO管脚定义即可使用。-The driver program of IIC simulation software, in order to modify the i2c.h header file IO pin definition can be used.
Desktop
- NRF24l01的接收和发送 基于STM32F103VCT6 用了硬件SPI1 对IRQ引脚使用了外部中断 来触发接收和发送完成、其他的中断 具体的引脚可以查看头文件-Send and receive NRF24l01 with hardware-based STM32F103VCT6 SPI1 right IRQ pin to trigger an external interrupt receive and transmit completion interrupt other specif
LCD12864
- ATMega16 的12864头文件与示例程序。 显示中文，并行控制。 可在头文件最开始处更改引脚设置-ATMega16 of 12864 files and sample programs. Display Chinese, parallel control. You can change the pin set at the very beginning of the header file