搜索资源列表
Uart
- 使用verilog语言实现FPGA与计算机串口的通信，包括clk分频，uart顶层文件，rx，tx。使用verilog-FPGA serial port to communicate with the computer, including the speed choose, uart top file, rx, tx. Use Verilog
main05182349
- 433M 遥控信号的接收解码，信号学习记忆，保存功能-433M RX
R5F100LE-USART-TX-and-RX
- 基于瑞萨单片机RL78的串口队列操作程序。利用串口中断和瑞萨的串口接受完成函数，实现瑞萨的串口中断队列接受功能。-Renesas RL78 microcontroller based serial queue procedures. Use serial port interrupt and Renesas serial reception complete function, enabling Renesas to accept the serial interrupt queue funct
URAT-VHDL
- vhdl版本的uart收发程序，方便实用-uart vhdl rx/tx
7)-CAN
- CAN communication code TX and RX code with PIC MCU-CAN communication code TX and RX code with PIC MCU...
C6455_Mcbsp_Test1
- c6455 MCBSP 发送接收例程。需要的可以参考。-c6455 MCBSP tx rx example
LPC11C14-and-Cotex-A8-Rx-and-Tx-Data
- 本源码主要是LPC11C14与Cortex-A8的通信，借助的是zigb-The main source is the communication LPC11C14 with the Cortex-A8, with the help of a zigbee
dsPIC33F_ABAUD_V1.0.0
- UART 接收引脚 （ RX 引脚）上的信号能在内部传送至一个输入捕捉模块以获得输入信号边沿的时序。根据该时序，应用程序能正确设置UART 的波特率。-The signal on the UART receive pin (RX pin) can be internally routed to an Input Capture module to time the edges of the incoming signal. From that timing the software can se
RF433_Rx877A
- CCS-C compiler source code for RF433 cheap wireless module receiving(Rx) using Manchester code in PIC16F877A
DigitalCompinacijaSimulacija
- It is a bridge between CPU and sensors where user can not connect sensors directly on CPU. It consumes very small number od LUTs and it is suitable for CPLD design. it works on following way, when logic detects falling edge of RX, then this action tr
nRF24L01P
- RX :收到一个数据后LED翻转一次。同时在OLED显示状态。 TX :成功发射一次后，LED翻转一次。同时在OLED显示状态。-RX: Upon receipt of a data LED flip once. At the same display state in OLED. TX: After a successful launch, LED flip again. At the same display state in OLED.
uart2bus_latest
- uart IP, including rx,tx module,and FSM control,data paser logic. including: testbench-uart IP
GPS_TX_RX_VERILOG
- GPS Tx RX verilog 19-GPS Tx RX verilog 1988
rf433
- 这是个完整工程，使用rf433/315M超再生模块(最便宜那种)通讯的接受程序。可以用电脑串口接发射模块按照doc文件夹里的说明编码实现通讯测试。可实现短距离传感器数据采集等。MCU为stm8s103f3p6, 编译环境为IAR for stm8.-Here s a completed project.RX decode using rf433/315Mhz super-regeneration moduler(yes,the cheapest one!). You can use PC to
AES_RX_pic18
- AES microcontroller 18f452 rx
18B20
- STM32控制温度传感器单总线上的所有通信都是以初始化序列开始。主机输出低电平，保持低电平时间至少480 us，，以产生复位脉冲。接着主机释放总线，4.7K的上拉电阻将单总线拉高，延时15～60 us，并进入接收模式(Rx)。接着DS18B20拉低总线60~240 us，以产生低电平应答脉冲。 -STM32 control temperature sensor u8 DS18B20_Check(void) { u8 retry 0 DS18B20
rxtx
- 简单的 RX TX串口发送接收模块 方便移植-Simple RX TX serial port to send and receive modules to facilitate transplantation
si4432
- stc单片机控制si4432无线模块发送接收程序-stc MCU control si4432 wirless module Tx and RX soft
e05mle132a
- NRF24LE1 GPIO UART 发送 接收 等例程-NRF24LE1 GPIO UART RX TX ....SOURCE CODE
Arduino_ublox
- Arduino uno板子 需先下载程序后接线，否则会下载失败 GPS模块VCC Arduino的5v GPS模块GND Arduino的GND GPS模块TXD Arduino的RX（数字IO 0） GPS模块RXD不接 GPS模块PPS不接 若使用Arduino leonardo板子 需要将代码中所有的Serial修改为Serial1-Arduino uno board Need to download the program after the w