搜索资源列表
C2812EVPWM.
- SPI(Serial Peripheral Interface--串行外设接口)总线系统是一种同步串行外设接口，它可以使MCU与各种外围设备以串行方式进行通信以交换信息。-SPI (Serial Peripheral Interface, Serial Peripheral Interface) bus system is a kind of synchronous Serial Peripheral Interface, it can make MCU communicate with a v
My_enc28j60
- enc28j60的网络模块调试程序，spi口的网口功能实现，可提供网口调试。 -Enc28j60 network module of debugging, implementation of spi mouth so function, can provide so debugging.
c8051F320NET
- C8051F320的程序调试，包括c8051f320+enc28j60的网口调试，LED，spi，电压表，uSB等的调试程序，非常实用，并且能够进行F320与F340的程序移植。-With C8051F320 program debugging, including the front-end ports with C8051F320+ enc28j60 debugging, LED, spi, voltmeter, such as uSB debugging program, very pra
FREQSYN
- 使用Verilog语言编写的使用SPI总线设置频率LM2346,可通过设置其R寄存器对其输出频率进行设置（需相应的射频电路相配合）。-The use of Verilog language use SPI bus frequency settings LM2346, can be by setting up its R register set of its output frequency (to be matched by corresponding RF circuitry).
A7125(AP243)
- 2.4G模块A7125进行接收的程序，使用的是SPI通信，时序要求不是很高，我测试了在不修改程序的情况下更换了12M，22.1184M等单片机都能正常使用。通信距离在200米左右。-2.4G module A7125 receive the program, using the SPI communication, timing requirements are not very high, I tested without modifying the program have changed
A7325
- 结合A7125或两个A7325可进行2.4G数据的传送。使用的是SPI通讯。这个模块同时具有发送和接收的功能。-Or a combination of both A7325 A7125 2.4G data can be transmitted. Using SPI communication. This module also has the function of transmitting and receiving.
STM32-SST25VF016B-Fatfs-ucgui-ucos
- 配合奋斗开发板使用。但是，其采用SPI FLASH作为存储，ucGUI与ucOS为屏幕驱动及操作系统，FatFS是文件管理系统。可以借鉴其中的编程结构及代码。-Struggle with the development board. However, its use as a storage SPI FLASH, ucGUI with ucOS to screen drivers and operating systems, FatFS is a document management syst
MPU6000
- Cortex M3 LPC1768单片机 通过IIC与SPI通信交叉读取MPU6000 三轴陀螺仪传感器的加速度 角速度。可用于运动物体姿态检测与倾角测量，可给产品带来较强的用户体验！-Cortex M3 LPC1768 microcontroller via SPI IIC communication with cross-axis gyro sensor reading MPU6000 acceleration angular velocity. Can be used for motion
spiPlpc17Pucos
- ucos下的LPC17系列的SPI驱动，操作EEPROM和FLASH等设备。-LPC17 series SPI driver under the ucos operation ,It can operate with EEPROM and FLASH devices.
STM32color_Screen
- STM32针对于SPI彩屏,采用模拟SPI，可显示图片，文字，数字，字符等。-STM32 to SPI color screen, using the SPI simulation, can display pictures, text, numeric, character etc..
1814_SPI
- 瑞萨公司UPD78F1814单片机硬件SPI程序，可支持与外部SPI器件硬件通信。-Renesas UPD78F1814 microcontroller hardware SPI procedures, can support with external SPI device hardware communication.
MCP2515
- CAN控制芯片MPC2515的控制程序，SPI接口，C编写-CAN controller chip MPC2515 control procedures, SPI Interface, C prepared
program
- lpc2103程序，实现spi通信（与ad7399），i2c与at24c04通信，可读写任意长度数据，实现485通信。 整个程序功能为：通过485接收PC机指令，执行i2c读写和spi通信，控制和保存ad7399电压输出。-lpc2103 procedures to achieve spi communication (with ad7399), i2c communication with at24c04, can read and write data to any length to
ATmega28-ADC
- AVR单片机的ADC和SPI程序，资料很不错，打击可以参考一下，呵呵。-AVR microcontroller ADC and SPI procedures, information is very good, you can refer to blow, huh.
7811
- 关于51单片机和dac7811芯片之间通信的程序，可以正确模拟SPI串口通信，写入数据-On communication between 51 single chip microcomputer and dac7811 chip procedures, can correctly simulate the SPI serial communication, write data
05.-DTK_BPD_SPI
- TI2812定时器成熟例程，可以为初学者使用-TI 2812 mature SPI routines, as beginners can learn to use
hello_sd
- 基于fpga verilog 语言和nios ii实现的spi模式下sd卡驱动，以及加入znfat文件系统的sd卡驱动，可读取sd卡内的文件。-Based on the language and under the fpga verilog realize spi mode nios ii sd card driver, and adding znfat sd card file system driver, you can read files sd card.
F02x_SPI0_Master
- 通用于c8051f02x的spi通信的主机程序，可根据需要进行改写-Generic host process in c8051f02x spi communication, can be rewritten as needed
Lcd
- 同步串口4行液晶的显示，可以汉字和字符混合显示，并且左对齐，右对齐，居中显示、自由显示都有了。例外还包括stm32f103的i2c,spi,已经队列，已经应用。绝对可靠。-Synchronous serial 4-line LCD display that can display characters and mixed character, and left-aligned, right-aligned, centered, freedom to display everything. Exc
DAC7611
- 这是用51的单片机控制DAC7611的C程序采用SPI控制，用两个独立按键控制DA的输出电压，每次步进值为0.1V，源程序可以直接使用。-This is controlled by the microcontroller 51 DAC7611 C program using SPI control, with two separate buttons to control the output voltage DA, each step is 0.1V, the source code can