搜索资源列表
stm32f105_usb_host_lib_example
- 不用多说,是STM32F105,107带USB otg的例程,一个是连接USB接口的鼠标和键盘,另一个是连接U盘的(例程中只支持FAT12和FAT16,即支持2G内的U盘,这个得注意)-Needless to say, is STM32F105, 107 with USB otg routines, one for connecting USB interface, the mouse and keyboard, the other is connecting U disk (routine o
stm32F105-07_F2xx_USB_Lib_V2.0
- STM32_F105-07_F2xx_USB-Host-Device_Lib_V2.0.0，适用于stm32f1的互联型系列和f2系列-STM32_F105-07_F2xx_USB-Host-Device_Lib_V2.0.0, for stm32f1 interconnected series and f2 Series
STM32F105和K9F4G08U0A 程序
- 用STM32F105外挂512*8 byte 的NAND FALSH K9F4G08U0A
STM32F105和K9F4G08U0A 程序.rar
- STM32F105外挂512*8 byte NAND FLASH K9F4G08U0A 程序
stm32f105-7_update_for_arm-mdk
- Update Keil uVision ARM MDK for support STM32F105 and STM32F107 processor (info files and erase/program algorith file).
SCH
- 火牛开发板stm32105的原理图文件，分享给大家-AC adapter development board stm32105 the schematic file, share it with everyone
SPI_interrupt
- STM32f105 program SPI interrupt, developed on MDK4.13
stm32f105gui
- stm32f105使用的GUI,速度超快.-stm32f105 use GUI, very fast.
STM32F105VC_K9F4G08U0A-
- STM32F105和K9F4G08U0A 接口程序.读ID；写0块，0页，然后读出。-STM32F105和K9F4G08U0A interface program.Read chip ID；WRITE0 BLOCK，0PAGE，THEN READ IT。
STM32F105_MMA7455L-CODE
- STM32F105和MMA7455L 3轴加速度仪接口程序.读3轴的数据（10位）并转换成浮点数。-STM32F105 and MMA7455L 3 axia accelerometer interface program：Read 3 axia data(10 bit),then convert into float data.
STM32F105_OBDII_CAN-CODE
- STM32F105和OBDII_CAN的接口程序。具体是测试 OBDII CAN总线的协议类型和速率，并读取VIN。-STM32F105 and OBDII_CAN interface program。detail is that Test OBDII CAN s rate and get Car VIN from OBDII.
stm32F105CAN
- MDK环境下实现STM32F105,双CAN中继的功能。-MDK environment the STM32F105, CAN relay function.
SAFE_IN_OUT_Soft_DialSW
- stm32F105芯片实现多通道开关量信号采集与多通道开关量信号输出，并通过CAN总线进行数据通讯-stm32F105 switch chip multi-channel and multi-channel signal acquisition switch signal output, and data communication via CAN bus
STM32F105
- STM32F105 MP3 coder and decoder sources.
STM32F105-CAN
- STM32F105 1、本双CAN开发板选用意法半导体的Cotex-M3的STMF105RBT6 ，内核72MHz，外设丰富，具有USB ，2 个CAN控制器等。 2、本开发板接口丰富，具有1路USART接口（USART2,USART1被USB接口占用了），2 路CAN接口(采用NXP 的TJA1040 收发器)，4 个LED 灯，复位按键，大量IO预留输出。仿真调试口采用SWD口，接口简单，可释放更多IO口使用。两路CAN均有保护电路，120Ω终端电阻跳线选择。一路USB接口，可用于USB
stm32f105-usb-hid
- MCU是stm32f105，将USB端口，驱动为HID，可以与pc通信，已经完成测试。-MCU is stm32f105, the USB port, driven by HID, can communicate with PC, has been tested.
AHMI_EB_v0100
- 采用STM32F105写的驱动7寸液晶屏(Drive 7 inch LCD screen using STM32F105)
ld01_02_20170816_v1_01
- 采用STM32F105和FPGA设计的驱动液晶屏的电路图。(Circuit diagram of driving LCD screen designed by STM32F105 and FPGA)
bootloader
- 实现stm32f105程序代码的远程升级的boot(Stm32f105 program code to achieve remote upgrade of the boot)
STM32F105_CAN
- STM32F105实现CAN通讯，可修改标准数据帧和扩展数据帧，远程帧。(stm32f105 realizes CAN communication)