搜索资源列表
Sources
- 采用DS18B20和STM32F103RBT6编写的测温程序，每秒从USART1输出温度数据。采用3.5版固件库，自编DS18B20库文件，需要注意的是使用本库前需要写delay_us和delay_ms函数。电路上采用8M晶振，PA8为数据口，如有变化请修改stm32f10x_conf.h文件。-The temperature program DS18B20 and STM32F103RBT6-written per second from USART1 output temperature d
STM32_USART1
- stm32 库文件：3.10 本程序是使用UART1接收中断,收到数据后直接把原数据从USART1发回去 一开机时,会发送 "Starting....."到USART1-stm32 Library: 3.10 This procedure is to use UART1 receive interrupt, received data directly to the original data sent back from USART1 A start,
usart1
- AMR_stm32f103的串口程序，利用中断方式进行接收。希望对大家有用。-AMR_stm32f103 serial programs, using the interrupt mode to receive. Want to be useful to everyone.
STM32-USART-DEMO-V2
- 演示 USART1 当接收缓冲器满时，将接收到的数据传送出去 V6-LED1闪烁表示正在收发数据。 -When the receiver buffer demonstration USART1 full, will receive the data transmitted V6-LED1 flashes that are sending and receiving data.
USART1
- stm32的串口程序，开发软件是keil4-Stm32 of serial program, develop software is keil4
USART
- 在万利199元开发板上实现了uCOS-II移植到STM32的操作，建立了LED闪烁任务以及USART1向计算机发送数据的任务。-Manley 199 yuan in the development board implements the STM32 uCOS-II ported to the operation, the establishment of the task and the LED flashes USART1 send data to the computer task.
STM32serial-port1DEMO
- 演示 USART1 当接收到结束符是0x0d 0x0a时，将接收到的数据传送出去V6-LED1闪烁表示正在收发数据。 -When the receiving end of the presentation USART1 operator is 0x0d 0x0a, will receive the data transmitted V6-LED1 flashes that are sending and receiving data.
2MSP430F149USART1sendreceivewithpc
- 使用MSP430F149芯片，透过串口与电脑发送接收通信，波特率9600,8数据，无校验。使用32.768k晶振，使用P3.6和P3.7口作为发送和接收口，使用异步通信USART1，采用中断形式。实现通信，当单片机接收到什么字符后，它会自动把接收的字符发送个电脑-MSP430F149 chip computer through the serial port and send and receive communication baud rate 9600 data, no parity. 32
5PC-sends-data-to-MSP430-P6P4-1-time
- 使用MSP430F149芯片，透过串口与电脑通信，波特率9600,8数据，无校验。使用32.768k晶振，使用P3.6和P3.7口作为发送和接收口，使用异步通信USART1，采用查询形式。实现通信，当单片机接收到以S结尾以W开始的字符串时，中间的数据最好是二进制的16位，单片机会把中间的数据高八位赋值给P6口，把中间的数据低八位赋值给P4口。-MSP430F149 chip through the serial port to communicate with the computer, bau
USART1
- 基于金牛开发板的C代码 usart1的测试代码，keil工程-Based the Taurus development board C code usart1 of the test code, keil project
USART1-polling
- USART1采用查询方式+ucos-iii实现-USART1 using queries+ucos-iii realization
STM32-screen-P-USART1
- stm32+ucos+ucgui编写的USART1通信例程-STM32+ UCOS_UCGUI serial communication routines written USART1
stm32-modbus-USART1-TIM2
- 用stm32的usart1和tim2模块实现了modbus从站协议。IAR编译环境。-usart1 and tim2 module implements modbus slave protocol. IAR compiler environment.
USART1
- SMT32 usart1(非阻塞) 中断接收，DMA发送
project2
- 本例程实现串行Flash的读写操作，并测试读写速度。采用STM32内置的SPI硬件接口访问串行Flash。 程序执行结果通过串口1（USART1）送到计算机的串口。可以通过PC机的串口超级终端软件观察程序执行结果。 上电后，打印例程版本信息和操作提示信息, 显示检测到的芯片ID。 用户可以通过PC机串口终端软件发送命令字符来控制程序运行。-This routine Serial Flash read and write operations, and test th
STM32F207VC-RS485-USART1
- STM32F207VC RS485使用USART1-STM32F207VC RS485 use USART1
modbus-STM32F103
- 利用STM32的定时器1和USART1实现MODBUS从站功能,具有读线圈,写线圈,读单个寄存器,写单个寄存器等功能,严格遵循ModBus通信规范。-Use STM32 timers 1 and USART1 implement MODBUS slave function, with read coil, write coil, a single register read and write single register functions, strictly follow the ModB
Uart_receive
- STM32F4系列串口接收函数,，程序已测试通过。-void USART1_IRQHandler(void) //串口1中断服务程序 { u8 Res #ifdef OS_TICKS_PER_SEC //如果时钟节拍数定义了,说明要使用ucosII了. OSIntEnter() #endif if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) //接收中断(接收
usart1
- avr atmega128 usart1 sample
stm32单片机通过USART1 收发数据
- stm32单片机通过USART1 收发数据通过串口调试软件，向板子发送数据，板子接收到数据后，立即回传给电脑。 库版本 ST3.0.0(STM32 MCU through the USART1 data through the serial debugging software to send data to the board, the board receives the data, immediately back to the computer. Librar