搜索资源列表
EasyARM-Software
- EasyARM2200开发平台试验用的通信软件，可以直接设置COM1与开发版通信-EasyARM2200 development platform test of communications software, COM1 can be directly set up communications with the development version
XSA2
- 这是在PC机或工控机上运行的程序,用PC机的COM1(0x3f8)口,和单片机通讯,波特率1200。
serial_communication
- 通过COM1与单片机通讯的界面程序，包含3个线程-Communications through COM1 and MCU interface process contains three threads
wireless_alarm
- 基于8051的网络远程控制系统 本项目通过网络实现远程监控，远程的电脑具有固定IP，在远程电脑的COM1的串行传输端口接一块8051控制板，然后以RS-232传输方式传输数据到8051的电路板，8051控制板上采用固态继电器（Solid State Relay）连接到电子产品，从而可以远程控制这些电子产品何时开启或关闭。8051控制板上还可以每分钟测量一次当前温度，再传输到远程监控端。-8051-based network remote control system for the i
my_boot(2440_UCOS_OK)
- 移植好的UCOS2.86版，能在2440上直接运行。（板的的晶振是16.9344M，用COM1来调试）-Transplantation UCOS2.86 best version that can run at 2440 directly. [The crystal plate are 16.9344M, used to debug COM1]
ex4_SCI
- 程序所在目录：ex4_SCI 采用标准DB9 串口直连线将PC 串口和扩展板串口相连。打开PC 上的串口调试软件。默认设置COM1,9600N,8,1。选择按16 进制接收和发送。 然后打开CC2000,进行如下操作： 1．Project->Open ，打开该目录中的工程文件。 2．Project->Rebuild ALL,编译链接 3．File->Load Program 4．Debug->GO Main 5．Debu
rs232
- 80c51和pc 机通过串行通信程序，电平转换用MAX232 (1)单片机端的数据传输程序 汇编或者c51 (2)pc机端的vb或者vc编写的通信程序 最好是vb (3) pc机 用的是com1 9针端口 -80c51 and machine through the serial communication pc procedures, level translators with MAX232 (1) single-chip end of the compilation
RTX_Traffic2
- ARM 7 LPC serial.c file altered to support both COM0 and COM1 with interrupts on MCB2300 evaluation board with LPC2368 ARM 7 microprocessor.
TestSerial
- ARM 平台下的串口测试源代码，支持com1-com9 ，支持多种波特率。基于evc4.0+sp4开发，可以直接编译使用。-ARM platform source code to test the serial port to support the com1-com9, supports a wide range of baud rate. Evc4.0+ sp4-based development, can direct the compiler to use.
877com
- pic单片机与PC通信，通过COM1控制PIC的AD开启； 编译环境：MAPLAB-pic microcontroller and the PC communicate via COM1 control the PIC' s AD open Build Environment: MPLAB
adc2051
- load 8051.dll load SUART xtal=11059200 mode com1 1200 assign com1 <sin >sout g,main ws TL0-load 8051.dll load SUART xtal=11059200 mode com1 1200 assign com1 <sin >sout g,main ws TL0
DDS
- ATMEl AT89X5x 系列单片机操作AD9834 DDS芯片的代码，使用COM1口，配置成移位输出方式。-this code illusrate how to control AD9834 DDS chip with ATMEL AT89X5X series MCU.the UART port of the mcu shoud be configured as shift output mode.
seriel_reciever
- this the code to communicate serialy by using com1.this code recive the character-this is the code to communicate serialy by using com1.this code recive the character
lesson1
- AVR单片机流水灯等试验（转自TXMCU，不得用于商业用途，谢谢）-AVR Microcontroller test water lamp, etc. (transferred from TXMCU, not for commercial purposes, Thank you)
Terminal
- 自己调试过的用com1口实现键盘和主机之间通信。-a tapical serial communacation
SPI
- 本开发板采用DB9 直通电缆把DSP 的串口和PC 的串口连接起来，打开PC 机的串口调试软件，默认设置为COM1,9600，N,8,1,选择按16进制接收和发送。 -The development board DSP with DB9 straight-through cable to PC serial port and serial port connected, open the serial port of PC, debugging software, the default is
jishuqi
- 一个9999的计数器，然后用4个数码管显示当前数值，数码管共用a到g口，通过com1到com4选通的- 9999 counters, then with 4 nixietube demonstration current value, the nixietube use in common a to g, through com1 to the com4 selection
VCPP
- 程序实现功能：1、 PC初始化COM1口，使用n81方式，波特率57600与单片机通信。-Program to achieve functional: 1, PC COM1 port initialization, the use of n81 mode 57600 baud rate communication with the microcontroller.
USART-COM1
- USART-COM1 神舟III号STM32F10x实验板-USART-COM1 Shenzhou III, STM32F10x breadboard
UART-COM1-experiment
- USART-COM1串口接收与发送实验-高级版(STM32神舟IV号-寄存器版)-UART-COM1 serial port to receive and send experiment- Advanced Edition (STM32 Shenzhou IV No.- register Edition)