搜索资源列表
cword
- cword 拆字的汇编程序 一般本程序用于把数据送显示缓冲区时用-split-assembly process generally cword This procedure is used to send data to display buffer time
nrf2401
- NAF2401的发送与接收程序，已通过测试，有键盘操作，键盘按的数据对应发出去-NAF2401 the sending and receiving process, has been tested to operate a keyboard, the keyboard according to the data sent to the corresponding
NewGpsUnit
- 该源码详细介绍了GPS获取数据及处理数据过程，很珍贵！-The source code details the GPS data and processing data acquisition process is very precious!
ad
- 模拟数据量输入到单片机处理，该程序阐述模拟量的全过程-Analog data input to the microcontroller processing, the program set out the whole process of analog
vxworks_introduction
- 本资料集给出了VxWorks开发的一些基本学习材料，涉及VxWorks应用程序、BSP的开发，系统启动过程描述、中断执行流程及原理等-This data set gives the VxWorks development of some of the basic learning materials, involving VxWorks applications, BSP development, the system boot process descr iption, interrupted
AD8555
- 放大器AD8555的程序，AD8555是一个单数据总线的放大器-Amplifier AD8555 process, AD8555 is a single data bus amplifier
decode
- ICCAVR下的红外解码程序,全部源码,原理图和PCB,芯片资料-ICCAVR under the IR decoding process, all the source code, schematics and the PCB, chip data
52234_PWM_ADC_LCD
- 自己编的Freescale 32位微控制器MCF5223x系列的AD模块、PWM模块、QSPI模块综合应用程序（通过程序设定PWM模块，产生所需频率和占空比的脉冲，经过AD采样后，通过QSPI总线将处理数据传输到LCD上显示成脉冲的真实波形）。适用于学习Freescale微控制器的同学使用-Its own series of Freescale 32-bit microcontroller MCF5223x series of AD modules, PWM modules, QSPI modu
testser
- wince串口数据转发程序，需要的可以-wince serial data forwarding process, need to take a look at
hdb
- 数字基带信号的传输是数字通信系统的重要组成部分。在数字通信中，有些场合可不经过载波调制和解调过程，而对基带信号进行直接传输。采用AMI码的信号交替反转，有可能出现四连零现象，这不利于接收端的定时信号提取。而HDB3码因其无直流成份、低频成份少和连0个数最多不超过三个等特点，而对定时信号的恢复十分有利，并已成为CCITT协会推荐使用的基带传输码型之一。为此，本文利用VHDL语言对数据传输系统中的HDB3编码器进行了设计。 基于达到达到达到的信号发生器的源程序-Digital baseband
ADS8422-C6416
- 该程序是AD8422开发板和DSP6416开发板连接实现数据采集的程序。-The program is AD8422 development boards and development boards to connect DSP6416 data acquisition process.
ov911
- ADI Blackfin处理器bf561使用OV911传感器进行图像采集的程序，使用I2C总线控制传感器，使用PPI接口接受图像数据-ADI Blackfin Processors bf561 sensors using the OV911 image acquisition process, use the I2C bus control sensors, the use of PPI interface to accept image data
SEEDVPM642_led
- DM642开发板的LED实验代码，内含BOOT程序，DSP上电自启动过程中，自动恢复RAM内应用数据-TI Series dsp Shaoxie during the BOOT process necessary to ensure the DSP power-on self-starting process, the application of automatic recovery of data RAM
ds18b20
- 详细说明：学习掌握单总线数字式温度传感器 DS18B20的64位激光ROM码的读出方法。读DS18B20 64位ROM码命令（33h）允许主机直接读出从机的64位ROM代码，而无须执行搜索ROM 过程。如果该命令用于多节点系统，则必然发生数据冲突，因为每个从机设备都会响应该命令。64 位激光ROM 从高位到低位依次由8 位CRC、48 位列号和8 位家族代码(28H)组成。--learning and mastering digital single bus DS18B20 64 laser
ZLG7289
- 此为基于ZLG7289和C51的程序，因为官方资料为64按键，而本人只用到其中16按键，所以程序关键是地址的选择-This is based on ZLG7289 and the C51 process, because official data for the 64 keys, but I only used 16 of them keys, so key is to address the choice of procedure
adc
- AD数模转换程序，是设计数据采集的一个参考c语言代码-AD digital-analog conversion process, is designed as a reference data collection c language code
s3c2410
- S3C2410处理器是Samsung公司基于ARM公司的ARM920T处理器核，采用0.18um制造工艺的32位微控制器。本文档是s3c2410的中文数据手册-Samsung' s S3C2410 processor is based on the ARM920T processor core, ARM, using 0.18um manufacturing process of 32-bit microcontroller. This document is the Chinese s3
ds18b20s4
- 四路DS18B20的verilog HDL 代码，精度为1℃无须转换数据，根据输入地址改变直接输出结果。占用600个LE资源，相对于单路程序，更为精减-Four DS18B20 the verilog HDL code, and an accuracy of 1 ℃ without converting the data, enter the address change in accordance with the direct output. Occupy 600 LE resources,
1602
- 这是一个关于LCD1602的初始化程序，包含有1602读状态，写指令，写数据，读数据等相关程序。-This is an initialization process on the LCD1602 includes a 1602 state reading and writing instruction, write data, read data and other related procedures.
usb
- A7102的USB烧录程序，包含工程文件和程序资料，程序包含注释，非A7102芯片自带程序。-A7102 of USB recording process, including project documentation and program data, the program contains comments, non-native program A7102 chip.