搜索资源列表
pcf_7705
- 通过对AD7705芯片的编写,使数据通过LED能显示,也是与单片机相关的程序,在KEIL C51里实现的。-Through the preparation of the AD7705 chip, so that data can be displayed through the LED, is also associated with the single-chip process to achieve in the KEIL C51.
MCS51programlibrary
- 本程序库中包含了RAM中数据操作,滤波,算术运算,等等汇编程序。-The library contains data RAM operation, filtering, arithmetic operations, and so the compilation process.
ht9032demo
- 在keil开发环境下实现的汇编程序,用51单片机控制ht9032芯片,读取FSK数据-Keil development environment in the realization of the compilation process, with 51 single-chip microcomputer control chip ht9032, the data read FSK
HDB3encoder
- 数字基带信号的传输是数字通信系统的重要组成部分。在数字通信中,有些场合可不经过载波调制和解调过程,而对基带信号进行直接传输。采用AMI码的信号交替反转,有可能出现四连零现象,这不利于接收端的定时信号提取。而HDB3码因其无直流成份、低频成份少和连0个数最多不超过三个等特点,而对定时信号的恢复十分有利,并已成为CCITT协会推荐使用的基带传输码型之一。为此,本文利用VHDL语言对数据传输系统中的HDB3编码器进行了设计。-Digital baseband signal transmission i
RTC
- 在嵌入式设计过程中,要涉及到实时时钟的设计,本资料提供一个对实时时钟的非常详细的讲解,为你的实时时钟的设计提供帮助。 -In the embedded design process, it is necessary to relate to the design of real-time clock, the data provide a real-time clock on the very detailed, real-time clock for your design to help
MSP430F149
- 用于过程控制的MSP430F149定时数据采集程序-MSP430F149 for process control procedures for data acquisition timing
Display
- 该C程序是基于MSP430的液晶显示程序,液晶是网上很流行的“27元超值液晶”。最近研究这个的人很多,这是一款手机液晶320*240,彩色TFT液晶。但是该液晶没有驱动芯片资料,所以,开发起来很困难,经过一段时间的努力,我已经实现了AD采样数据动态显示(示波器),图像显示等功能。-The C program is based on the MSP430 process of liquid crystal display, liquid crystal is a very popular line
2008-04-23
- 这是一整套USB2.0试验程序,包括单片机程序(用的是C8051F020),USB2.O芯片(68013)的固件,PC端读取USB数据并画波形的程序(VC编写)。这套程序实现了单片机和PC的USB通讯,可以帮助初学的朋友入门。-This is a set of testing procedures USB2.0, including single-chip process (using the C8051F020), USB2.O chips (68,013) of the firmware,
ATMAGE128uartasksendinterruptreceive
- 本程序经调试好使,如果程序不好使,请注意检查更改波特率和晶振频率以及检查调试助手和单片机的熔丝位设置,尤其是103兼容模式的熔丝位不编程M128和M16串口通信程序大同小异,M128有两个串口UART0、UART1而M16只有一个串口UART,只需要修改相应的寄存器和引脚设置即可中断方式接收能有效防止(采用查询方式接收)单片机外部设备不正常,不能收到数据死机-After debugging the program so that, if the process not so, please no
1020
- 课程 1020 BTL: 16位自举程序的概念和实践 课程简介 本课程介绍目前的16位自举程序方案并全面概述高级模块化的自举程序概念。将具体介绍目前的16位自举程序的详细 情况,包括C数据结构、C和汇编函数以及一些协议细节。本课程还将演示一个运行于16位单片机上的小型串行自举程 序。还会讨论高级模块化的自举程序概念,包括通信层模块的设计、实用的自举程序诊断、加密、各种进入/退出方式 和常见的应用程序调用的原因等。-Course 1020 BTL: 16
8051f040uartsendtoHF
- 新华龙C8051F040单片机程序,与串口连接,收发数据经调试好使-Hualong C8051F040 new single-chip process, and the serial port to connect, send and receive data so that debugging
1820
- ds18b20检测温度,12864显示测得的温度值处理后得数据。包含处理过程。-Detection ds18b20 temperature, 12864 showed that the measured temperature data after treatment. Contains process.
se_IO_485_5
- 单片机IO口仿485发送数据,经长时间测试极为稳定,为资源紧缺的单片机扩展资源不可缺少的程序-IO I like single-chip 485 to send data, after a long time to test is extremely stable, single-chip resource constraints for the expansion of resources indispensable to the process
waibuzhongduan
- 采用外部中断INT0(用按键BUTTON模拟)中断,单片机P2口为输出口外接两位LED数码管。每申请一次中断(按下BUTTON),在中断处理程序中对数码管的显示数据作加1改变(实验中P2口外接的两位LED数码管采用7447硬件译码的方式以BCD码显示)。-The use of external interrupt INT0 (with simulated BUTTON button) interrupt, microcontroller P2 output port for an externa
ISPAVR
- 简单的并口下载AVR程序资料,有接线图和下载软件和软件设置图-Parallel port AVR simple process to download data, there are wiring diagram and software to download the software and set up plans
pcf8563
- pcf8563的读写程序头文件,内部有简单的数据结构,可以直接调用。-pcf8563 process of reading and writing header files, internal data structures are simple, you can call directly.
model_monitor_ram
- 单片机程序调试小子程序,编入需调试程序中,在需要时CALL一下就把内存数据全部通过串口发送到上位机实时检查内存变量了-Single-chip debugging minimal procedures to be incorporated into the debugging process, in case of need they CALL you all through the memory data is sent to the host computer serial real-time
rtdx
- DSP实时开发程序 实现数据由主机到目标板的实时传输-The development of DSP real-time process data from the host to the target board' s real-time transmission
pid_temperature_controller_pt100_89c52
- pid temperature controller for pt-100 sensor, 8 digit display (4 digit for process temperature & 4 digit for set temperature), 4 key for parameter entry, 24c02 for data save.
DSP_Basic_development_program
- 1.DSP基本开发实验(熟悉CCS和DSP基本开发流程) 2.I/O控制实验(获取按键值并驱动LED显示) 3.中断设计实验 4.定时器实验 5.DMA实验 6.McBSP1接口实验 7.DSP/BIOS实验 8.音频Codec芯片AIC23数据采集回放实验 9.离散傅立叶变换DFT 10.无限冲击响应滤波器(IIR)算法实验 11.有限冲击响应滤波器(FIR)算法实验 12.实数快速傅立叶变换(FFT)算法实验 -Basic developmen