搜索资源列表
XXGDrv
- 中科院许西刚博士编写的USB的ＷＤＭ驱动程序。-Hsu Hsi just CAS prepared by Dr. USB WDM driver.
H30
- 用伟福Lab2000P单片机实验仪上80C196的HSI功能统计输入的脉冲个数。可以用板上500KHz信号和单脉冲的输出相‘与’得到一定个数的输入脉冲。
LED
- STM8SLED例程，使用HSI为系统时钟源，并配置恰当的分频比； TIM2 CC2 输出PWM信号控制LD2亮度； TIM3 CC1 输出PWM信号控制LD3闪烁频率； TLI（PD7）中断用来打开/关闭LD4.-STM8SLED routine use of HSI for the system clock source, and configure the appropriate divide rat
CSS
- 将时钟源由HSI切换到HSE； 使能CSS功能；LED闪烁。-HSI clock source is switched to the HSE enable CSS feature LED flashes.
Music
- 使用HSI为系统时钟源，并配置恰当的分频比； Timer2 CC1通道配置为PWM模式用以驱动蜂鸣器； Timer4 溢出中断用作LD4，LD3，LD2闪烁的时基； TLI（PD7)中断（用户按键）用来切换音乐的音调；-Use the HSI for the system clock source, and configure the appropriate divide ratio
UART
- 使用HSI为系统时钟源，并配置恰当的分频比； LINUART配置为UART模式-Use the HSI for the system clock source, and configure the appropriate divide ratio LINUART configured for UART mode
Sinwave
- 使用HSI为系统时钟源，并配置恰当的分频比； Timer1 CC1，CC2，CC3通道配置为PWM模式；-Use the HSI for the system clock source, and configure the appropriate divide ratio Timer1 CC1, CC2, CC3 channel is configured to PWM mode
EKSTM3210_v5_examples
- STM32时钟学习笔记(2010-01-27 09:23:15)转载标签：杂谈 分类：嵌入式 在STM32中，有五个时钟源，为HSI、HSE、LSI、LSE、PLL。 ①、HSI是高速内部时钟 8M，RC振荡器，频率为8MHz。 ②、HSE是高速外部时钟，可接石英/陶瓷谐振器，或者接 外部时钟源，频率范围为4MHz~16MHz。 ③、LSI是低速内部时钟，RC振荡器，频率为40kHz。 ④、LSE是低速外部时钟，接频率为32.768kHz的石英晶体。 ⑤、PLL为锁
80C196KB_UsersGuide_intel
- intel 196单片机手册，讲了单片机内部寄存器配置，io，hsi，等等好些东西。对于196单片机使用者这个文件是必须的 -SCM manual intel 196, speaking of the microcontroller internal registers configured, io, hsi, so better things. 196 MCU file for the user is required
SCM-program
- 用HSO.0输出脉宽为2ms，周期为3ms的方波，用HSO.2输出脉宽为3ms，周期为6ms的方波，并用HSI检测HSO.2输出方波的频率和脉宽。将测量结果循环显示在LED上，要求脉宽值和频率值各显示10秒。-HSO.0 output pulse width as 2ms, cycle square wave 3ms, HSO.2 output pulse width as 3ms, the cycle is 6ms square wave, and using the HSI Detect
SYS_conf
- STM32F407时钟，中断配置头文件，该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化； PLL时钟配置，PLL,SYSCLK，HCLK,PCLK1，PCLK2时钟的配置； RCC,GPIO,EXIT,NVIC的配置；-STM32F407 clock, interrupt configuration header file that contains the HSE, HSI, LSE, LSI, I2S, MCO clock initialization PLL
sys23
- STM32F407时钟，中断，精确延时配置，该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化；PLL时钟配置，PLL,SYSCLK,CLK,PCLK1，PCLK2时钟的配置；RCC,GPIO,EXIT,NVIC的配置.-STM32F407 clock, interrupt, precision delay configuration, the file contains HSE, HSI, LSE, LSI, I2S, MCO clock initialization PL
RCC1
- This example shows how to use, for debug purpose, the RCC_GetClocksFreq function to retrieve the current status and frequencies of different on chip clocks. You can see the RCC_ClockFreq structure content, which hold the frequencies of diffe
hsi
- hsi总线的linux驱动源码，完成hsi总线中断管理和收发-Hsi bus driver code based on linux
stsw-stm8052
- STM8S单片机关于HSI时钟校准的应用及相关例程-STM8S microcontroller applications on HSI clock calibration and related routines
system_stm32f10x
- The setting of system_stm32f10x.h when use HSI to set sysclk.-The setting of system_stm32f10x.h when use HSI to set sysclk.
16-RCC—使用HSE或者HSI配置系统时钟
- stm32f103的程序例子是RCC配置时钟的简单程序(The STM32F103 program is a simple program for configuring the RCC clock)
rtmp-ar030.tar
- 基于海思3518芯片的rtmp推流应用， 可自定义指定推流地址。(Based on the HSI 3518 chip RTMP push flow application, you can specify the push flow address.)