搜索资源列表
JN-AP-1002-Light-Switch-Application-1v6
- jennic jn5139模块 无线遥控灯代码
JN-AP-1012-Battery-Level-Monitoring-1v1
- jennic jn5139模块 电池电量监控程序代码
JN-AP-1040-UsingDioInterrupts-1v0
- jennic jn5139模块使用io引脚作为中断线的代码
JN-AP-1037-SleepModes-1v1
- jennic jn5139模块的睡眠模式代码
JN5139
- 关于zigbee厂家jennic的zigbee通信模块JN5139的一些示例程序。
Lab704-IEEE802.15.4
- CodeBlocks工程, 在Jennic JN5139开发板上基于IEEE 802.15.4开发的简单应用程序-CodeBlocks Projects, A simple application developed on the Jennic board JN5139 based on IEEE 802.15.4
ZigBeeLightSwitch
- 基于JN5139 zigbee 无线灯控代码-JN5139 zigbee-based wireless lighting control code
WUart
- 无线uart基于jn5139的zigbee协议-The zigbee wireless uart protocol on jn5139
BatterySensor
- 基于jn5139无线通信节点的数据采集实验-Wireless communication nodes based jn5139 Data Acquisition Experiment
Test_DioInterrupts
- 关于JN5139这款SOC芯片的Dio中断测试程序代码。开发环境用的是JENNIC公司的Jennic CodeBlocks软件。-SOC on the JN5139 chip Dio interrupt this test program code. Development environment using a JENNIC company Jennic CodeBlocks software.
Test_BatterySensor
- 基于JN5139这款SOC芯片的数据采集程序，利用GAINSJ开发套件上的温湿度传感器，将测得的温度，湿度值通过PC机的串口调试助手最终显示到PC机上。开发环境为Jennic CodeBlocks软件，使用C语言编写。-This SOC based on JN5139 chip data acquisition program, using GAINSJ development kit on the temperature and humidity sensors, the measured t
BaseIEEE802.15.4
- 利用JN5139实现2个节点之间基于IEEE802.15.4标准的通信。网络拓扑结构为星型，节点一个为Coordinator节点，一个为Enddevice节点。开发环境为Jennic CodeBlocks软件，用C语言编写。-Used to achieve two nodes JN5139 IEEE802.15.4 standards-based communication. For the star network topology, node 1 as the Coordinator nod
Test_ADC
- JN5139芯片自带的ADC接口（12bit），最快采样频率27.8K，该程序将GAINSJ开发套件上的模拟电压（电池电压）通过ADC转换成数字信号，并通过串口传到PC机上显示出来。开发环境为Jennic CodeBlocks软件，采用C语言编写。-JN5139 chip onboard ADC Interface (12bit), the fastest sampling frequency of 27.8K, the program will GAINSJ Development Kit o
JN-AN-1006-PER-Test-3v3
- This Application Note illustrates Packet Error Rate (PER) testing using a Jennic JN5148 or JN5139 evaluation kit. PER testing can be used to evaluate the communication range achievable in different operating environments.
Source
- JN5139 串口测试程序，详细说明请查看程序后面注释。-JN5139 serial port test program details, please see the program behind the comments.
BOCCN-MSG-v4.0(OK)
- 基于jennic jn5139的无线UART传输。-Based on jennic jn5139 wireless UART transmission.
JN5139
- 应用英国jennic公司生产的无线传感器网络芯片JN5139进行基本的组网设计的程序！-British jennic company production of application of wireless sensor network chip JN5139 in basic network design program!
WSN-chuan
- 应用英国jennic公司生产的无线传感器网络芯片JN5139进行串口通讯程序的设计！-British jennic company production of application of wireless sensor network chip JN5139 for serial interface communication program design!
JN5139_ZIGBEE
- 基于JN5139的ZIGBEE模块用于同环境监控数据采集仪进行无线通信，进行数据的组包分包与处理。中心节点与子节点自带RS232/485串口，AD转换口以及DA输出口。-Environmental monitoring data collection instrument based on the The JN5139 the ZIGBEE module is used with wireless communications, data group packet sub-processing.
jn5139
- zigbee 无线通讯模块程序代码，电池电量代码，电池电量检测，jn5139嵌入式软件程序，详细的程序说明文档-zigbee jennic jn5139 nxp code