搜索资源列表
PCBwzlct
- FLASH制作的PCB电路板加工整个流程,难得珍贵-FLASH produced by the PCB processing the entire process, rare precious!
642Faq
- DSP精华问答.为642使用过程中,遇到的一些问题及解决办法-DSP essence quiz. The use of the 642 process, the number of problems encountered and solutions
FPGAdesignstudy
- 介绍了FPGA设计全流程 和一些简单的例子-introduced FPGA design the whole process and some simple examples
CCSDSK5402ADPCM
- 这是基于DSP的语音压缩程序的程序,拿出来和大家一起学习-This is a DSP-based voice compression process procedures, and to show everyone learning together
mpegdsp
- 这是一个基于DSP的MPEG解码程序,实现MPEG格式视频数据的解码-This is a DSP-based MPEG decoding process to achieve MPEG video decoder
7led
- 7段发光二极管vhdl程序,可以验证led的fpga验证程序-seven of the light-emitting diode VHDL procedures can verify they simply led to the certification process
Lab15-PWM
- PWM输出实验 1) 熟悉LF2407的事件管理模块 2) 学会用通用定时器产生PWM波 一个简单的pwm波产生程序! -PWM output experiment 1) LF2407 familiar with the incident management module 2) how to produce generic timer a simple PWM wave PWM wave of a process!
a_filter
- 一种滤波程序,主要是用在信号处理方面的,-a filtering process, it is mainly used in signal processing.
hamming_decoder
- 汉明编码和解码的VHDL程序,直接解压就可以了-Hamming encoding and decoding process of VHDL, can be directly extracted a
PLCprograms
- 一个关于PLC的学习程序! 能让你在初学阶段快速掌握PLC编程-a PLC on the learning process! Can you grasp the learning phase PLC Programming
kongzhi
- 从其它网站看到的程序,框架不错,做单片机控制很有参考价值。后缀改为.c即可-from other sites to see the process, the framework is true, do MCU control of great reference value. Suffix changed. C can
uccos
- 有关ARM开发的程序,是基于uccos操作系统的开发.-the ARM development process is based on uccos operating system development.
9200boot
- AT91RM9200的boot程序,还不错的,外部时钟为12M-AT91RM9200 the boot process, but also good, the external clock to 12M
DES3200USBfirmwareV12
- 这是我编一个DSP的USP的程序 调试通过-This is Part I of a DSP USP through the debugging process
arm8019
- 开发工具用EMBEST IDE进行开发,该程序是一个S3C44B0直接驱动网卡的程序,包括8019初始化,物理层收包发包,UDP的接收和发送,IP的发送和接收.已及ARM的地址解板,整个程序是自顶而下,方便进行网卡研究用,也可将其移植到8051单片机上使用-development tools used EMBEST IDE for development, the program is a direct drive S3C44B0 card procedures, including 8019
LCD_DR
- //使用说明: //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出, //键值返回信号从keyscan低4位读入, //故使用时硬件电路需要与之相对, //或者把软件中相应地方修改即可-/ / use : / / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1
44scan
- //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出, //键值返回信号从keyscan低4位读入, //故使用时硬件电路需要与之相对, //或者把软件中相应地方修改即可-/ / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1 / / scanning proces
AD574keilC
- AD574keilC程序实像AD转换,用C编写的程序-AD574keilC process does as AD conversion, C preparation procedures
ds1624cprogram
- 由于DS1624是I2C总线结构的串行数据传送,它只需要SDA和SCL两根线完成数据的传送过程。因此,我们在进行程序设计的时候,也得按着I2C协议来对DS1624芯片数据访问。有关I2C协议参看有关资料,这里不详述。对于AT89S51单片机本身没有I2C硬件资源,所以必须用软件来模拟I2C协议过程。 要从DS1624中读取温度值,首先启动DS1624的内部温度A/D开始转换,对应着有相应的命令用来启动开始温度转换,有关DS1624的指令集参考前面的叙述。一般情况下,DS1624经过一次温度
Lab537-JPEGMotion
- Lab537-JPEGMotion开发的dsp程序,可以实现两个采集,同时显示3路,其中两个为采集的图像,另一路为前两路的运动。-Lab537 - JPEGMotion dsp development process, can achieve two collection, three road shows, two of which collected images of the other route for the former two-way movement.