搜索资源列表
DesignCompiler
- Design Compiler使用简要说明,说明了用这一工具进行综合的过程 -use Design Compiler brief statement, the use of this tool for integrated process
doubleuartkaifa
- 在应用PHILIPS的低档ARM的开发程序采集数据-in the application of low-grade ARM's development process data collection
wavegenerator_testbench
- 此文件采用了verilog语言在cpld中怎样实现波形发生器,及其验证程序-this document using the Verilog language in the cpld How to achieve waveform generator, and the verification process
ccontrol
- c语言编制的控制步进电机正反转,并且测试电极的启动速度及控制步进电机加速过程fft并画图的小程序-the stepper motor control reversion, test electrode and the launch speed and stepper motor control fft and accelerate the process of drawing small programs
arm_FS44B0XI_BIOS
- 一个F44b0启动的BOOT程序!仅供ARM学习者参考。-F44b0 start of a process BOOT! ARM learners reference only.
kchap9
- 在USB 固件程序设计中的主循环程序-USB firmware design of the main recycling process!
volume1
- 演示一个ccs的调试过程,下载就可以应用的,体验一下CCS的调试基本方法-ccs a demonstration of debugging process, can download the application, to experience the CCS debugging basic methods
RC_filter
- 计算RC(阻容)滤波时间常数的程序,有两种单位制,适合matlab65环境运行。 -calculated RC (R) filter time constant of the process, there are two unit system, matlab65 environment suitable for running.
HWMP3DECODER
- 外挂硬盘式解码程序,Keil语言编写验证-external hard-decoding process, Keil language test
7290C-datebase
- 此软件包包含了模拟I2C C51程序软件包和ZLG7290的C51程序然后包。 软件包的接口界面: (1) bit ISendByte(uchar sla,uchar c) (无子地址)写单字节数据 (现行地址写) (2) bit IRcvByte(uchar sla,uchar *c) (无子地址)读单字节数据 (现行地址读) (3) bit ISendStr(uchar sla,uchar suba,uchar *s,uchar no)(有子地址)读N字节数据
VBnet_MBMaster
- wince平台 modbus通讯 modbus tcp master vb.net的一个例子程序-Jack Modbus communications platform Modbus master vb.net tcp an example of the process
dianjicesu1
- 单片机开发程序,用以直流电机测速,并把所得值在七段数码管上显示出来。-MCU development process for the DC machine guns, and the values obtained in paragraph 107 of digital tube displayed.
1288711111
- 是有关于12887的初始化的一些处理,可以工参考-is on the 12,887 of the initialization process, and the Public Reference
PMSMFOCchengxu2407
- 该软件是关于PMSM永磁同步电动机磁场定向控制的汇编程序,对应的DSP处理器是TMS320F2407,解压后会出现CCS开发环境下的整个工程。-on PMSM permanent magnet synchronous motor magnetic field oriented control of the compilation process, the corresponding TMS320F2407 DSP processors, extracting CCS will happen af
SensorlessBLDCDriveControlAssemblyCode
- 该软件是关于无刷直流电动机调速控制的汇编程序,对应的DSP处理器是TMS320F24xx,解压后会出现CCS开发环境下的整个工程。-on brushless DC motor speed control the compilation process, the corresponding DSP processor is TMS320F24xx. extracting CCS will happen after the development environment of the whole p
TMS320C31DCCode
- 该软件是关于交流异步电动机直接转矩调速控制的汇编程序,对应的DSP处理器是TMS320C31,解压后会出现CCS开发环境下的整个工程。-The software is on the exchange of direct asynchronous motor torque speed control the compilation process, the corresponding TMS320C31 DSP processors, extracting CCS will happen afte
TMS320F240FOCSoftware
- 该软件是关于交流异步电动机磁场定向调速控制的汇编程序,对应的DSP处理器是TMS320F240,解压后会出现CCS开发环境下的整个工程。-The software is on the exchange of field - oriented asynchronous motor speed control the compilation process, the corresponding DSP processor is TMS320F240. extracting CCS will happ
chuankoumoli
- 用单片机软件模拟串口程序,只占用一个T2资源,对初学者很有帮助-MCU serial process simulation software, only takes up a T2 resources useful for beginners
anglemachine
- 《角度测量器》 用光电编码器测量角度,每个脉冲为0.72度。 测量范围:0.0~360.0度 为保证不错过脉冲,用timer1计数,在电平跳变中断里判断转动方向,尽量加快处理过程。 数据换算和数码管扫描显示在主循环中实现。 译码器用10米长5芯屏蔽线与数显器的两片74HC595连接。 MCU为12F629,使用内部4兆RC振荡和内部复位功能。 -"angle measuring device" using photoelectric encoder
p126
- 基于ARM的嵌入式系统Bootloader启动流程分析.pdf-ARM-based embedded systems analysis process launched Bootloader. Pdf