搜索资源列表
扩展_野火M3-USART2（polling）
- stm32f103例程：usrt的使用扩展2。来源野火开发源码例程(STM32F103 routine: use of USRT 1. Source wildfire development source routines)
I2C
- STM32F103的硬件IIC读写24C02程序(STM32F103 hardware IIC read and write 24C02 program)
EKBoard
- stm32f103开发板资料，以前使用的，可以测试通过(STM32F103 development board information, previously used, you can test through)
zetSPI实验 +SD卡+GPS+USB
- 使用stm32f103单片机实现数据的采集和存储到SD卡中(The use of STM32F103 MCU data acquisition and storage to SD card)
工程模板 - UCOS III
- stm32f103系列ucosiii模板(STM32F103 series ucosiii templates)
频率接收
- STM32F103与FPGA的串口通信，波特率4800，采用单向通信的方法。(Serial communication between STM32F103 and FPGA)
Project_Rf24l01
- 基于 STM32F103 单片机在 MDK(KEIL5)平台下对 RF24L01 无线模块的开发例程(STM32F103 microcontroller based on the MDK (KEIL5) platform for the development of RF24L01 wireless module routines)
MB001U
- 基于STM32F103 IMU开发，CAN通信(Based on STM32F103 IMU development, CAN Communications)
STM32F10x_硬件I2C从机（接收数据 - 中断方式）
- 实现STM32F103单片机作为主机与其他单片机进行通信(STM32F103 microcontroller as a host to communicate with other microcontrollers)
STM32串口UART4UART5
- STM32F103单片机对串口4和串口5的驱动程序。(UART4 and UART5 driver for STM32F103.)
STM32 IIC
- 针对STM32F103操作AT24C512的驱动程序,24C02~24C512均支持。(AT24C512 driver for STM32F103.)
STM32F103RCT6 ziliao
- stm32f103开发板资料，有程序，有电路图有芯片资料(STM32F103 development board information, procedures, circuit diagrams, chip data)
STM32 PWM
- 使用stm32f103 实现pwm输出 库函数操作(Using STM32F103 to achieve PWM output library function, using STM32F103 to achieve PWM output library function operations)
IIC
- 基于stm32f103，与I2C之间的通信(Communication between STM32F103 and I2C)
16-RCC—使用HSE或者HSI配置系统时钟
- stm32f103的程序例子是RCC配置时钟的简单程序(The STM32F103 program is a simple program for configuring the RCC clock)
FreeRTOS实验4-3 FreeRTOS任务挂起和恢复实验
- STM32F103 的freeRtos的操作系统中，任务的挂起和恢复(n STM32F103's freeRtos operating system, tasks hang up and resume)
点亮LED
- 基于stm32f103系列开发板顺序点亮LED灯，实现跑马灯效果(STM32F103 series development board based on the order of the LED lights, to achieve marquee effect)
RGB_model_code
- 通过SPI操作WS2812B（带IC的5050RGB灯珠）(Control WS2812B with STM32F103 SPI interface)
DHT11STM103
- STM32F103能实现温湿度的检测的代码，工程文件直接打开就可以用(Temperature and humidity detection can be achieved)
HJduino
- 核心板为stm32f103，该小车红外遥控代码是在keil 5 环境下用c语言编写的程序。实验多次，稳定性好，并且有相应注释，可灵活更改相关数据。(Core board for STM32F103, the car infrared remote control code is in the Keil 5 environment, written in C language program. Experiments many times, good stability, and correspo