搜索资源列表
sinmdlmatlab
- 正弦波在dspbuilder下产生VHDL源码及其测试激励文件的matlab模型,在modelsim下仿真通过-sine wave in dspbuilder under VHDL source code and test incentives document matl ab model, the simulation under through modelsim
wave.rar
- 波形发生器，Visual C++ 6.0、DDK和keil C51 uVision2 开发，含usb驱动,Waveform Generator, Visual C++ 6.0, DDK and keil C51 uVision2 development, with usb drive
wave.rar
- 用qwt所作的一个波形采集的源码,能够显示波形，现在固化为正弦波，以后可以装上自己的采集信号。,waveform acquisition with qt in qwt
pic16f627
- PIC 16F627 based PWM square wave inverter. Full schematic and hex file is included.
DDS
- 我们小组共了一个月做的DDS,程序核心用的是Verilog HDL,有仿真波形,输出正弦波,方波,及三角波,步进可调.频率范围1HZ--10MHZ-Our group for a month to do a total of DDS, the procedure is used in the core of Verilog HDL, there are simulation waveform, the output sine wave, square wave and triangular wa
wavegenerator
- 开发环境为QuartusII，能产生正弦波、三角波、方波和锯齿波，幅度为5V，采样为8位，在开发板已经验证通过，有详细的波形图和管脚分配图。-Development environment for QuartusII, can generate sine wave, triangle wave, square wave and sawtooth wave, ranging from 5V, sampling for 8, in the development board has to verif
full-wave-rectifier-circuit
- 10种精密全波整流电路。可以直接拿来就用，在电源方面利用-10 kinds of precision full-wave rectifier circuit. Can be directly brought on the use, in power to make use of
wave
- 可控脉冲发生器的VHDL源代码。设计文件加载到目标器件后，按下按键开关模块的S8按键，在输出观测模块通过示波器可能观测到一个频率约为1KHZ、占空比为50 的矩形波。按下S1键或者S2键，这个矩形波的频率会发生相应的增加或者减少。按下S3键或者S4键，这个矩形波的占空比会相应的增加或减少。-Controllable pulse generator of the VHDL source code. Design documents loaded to the target device and p
sinewave_c
- 在ccs上使用定时器实现一个数字震荡器的代码.产生的是正弦波波形。-Ccs use in the realization of a digital timer oscillator code. Sinusoidal waveform is generated.
GuidedLamb
- 文章讲述了板波在复合板中的传播，对于初学导波的人脚有用-Guided Lamb Wave Propagation in Composite Plate’Concrete Component
at89c52t0
- 使用单片机，正弦波发生器，key0口按键减小输出频率，key1口按键增加输出频率 sinout口输出正弦波，（cosout口输出余弦波），使用定时器T0，16位定时模式。 R6、R7用作10毫秒延时寄存器。Fout输出方波。且输出的正弦波在0.01-83Hz范围内，方波在1.3Hz-10.6kHz范围内。-The use of single-chip, sine wave generator, key0 I reduce the output frequency keys, key1
wave
- 这是我自己做的带触摸屏的波形发生小程序，希望对大家能有所帮助，不妥之处还请多多指教。-This is done with my own touch-screen waveform minor procedures, in the hope that we can help, please also wrong with the exhibitions.
signal
- verilog写的串口控制信号发生器，能通过用串口控制产生正弦波方波等信号-written in verilog serial control signal generator, can be generated using serial control, such as sine wave square wave signals
DAC
- 频率、幅度、占空比可调方波，有proteus仿真，可通过示波器查看，按键 12调整频率 34调整幅值 56调整占空比 -Frequency, amplitude, variable duty cycle square wave, and proteus simulation, can be read through the oscilloscope, adjust the frequency of 34 keys 12 to adjust the amplitude to adjust th
fangbo-ji[in
- 键盘输入，1602lcd输出，可选功能：输入可变频率方波、测2~15khz频率方波的频率计（测量有误差） 初学所做，请改进-Keyboard input, 1602lcd output, optional features: a variable frequency square wave input, 2 ~ 15khz frequency measurement of the frequency square wave (measurement errors) made by begin
12864wave
- 用C51驱动CM12864，在12864上显示正弦波-C51 driven by CM12864, sine wave shown in 12864. .
1024
- 用C写的mif文件正弦波数据文件，很好用的数据哦-Written by C sine wave data file mif file
L298andxiaoche
- 用keil 52写的L298的驱动程序。其中pwm波由软件仿真产生，用定时器实现，能够同时产生两种不同的PWM波从而实现两个电机的不同转速。经过测试通过。-Keil 52 written by the L298 driver. Pwm wave which generated by the software simulation, using timers to achieve, can produce two different kinds of PWM wave in order to ac
fullsine
- This a code for sine wave generation in modelsim. The code is written in verilog. An LUT has to be added to this program to work completely.-This is a code for sine wave generation in modelsim. The code is written in verilog. An LUT has to be added t
To-produce-the-1mS-wave
- 51单片机的定时器0产生1ms的方波,在P1.2引脚输出。-Timer 0 of 51 MCU generates 1ms wave in pin P1.2 .