搜索资源列表
FPGA2FPGA-Comms
- LAbview Program file to generate VHDL code shows the communication between two FPGA ICs.
Image-Reduction-IP
- LABVIEW Program for Image REduction IP for FPGA
Control-of-light-emitting-diodes
- 用labview控制一盏灯亮的客户端程序,实现与单片机的通信-Labview to control a light client program to achieve communication with the microcontroller
LockKeyMouse
- 本程序包主要演示在Labview下如何锁定键盘和鼠标的四种不同的方法; 在一些特定的测试应用上,测试设备需要对键盘与鼠标进行锁定防止操作人员对测试设备进行不必要的操作导致异常出现-How to lock mouse and keybd based on labview, this examples demostrate four methods to do it.
temperture
- 基于DS18B20的温度采集VI源代码,使用串口传输数据-VI source code, based on DS18B20 temperature acquisition using the serial port to transfer data
jiaotongdeng
- 使用labview实现的交通灯控制,可以实现基本的红绿灯,黄灯功能,但是没有转向灯-Use labview to achieve traffic light control, you can achieve the basic traffic light, yellow light function, but no turn signals
traffic-lights
- 一个简单的交通灯控制系统,没有故障处理功能-A simple control system for traffic lights, no fault processing function
Sinusoidal-Filter
- 这是一个简单的正弦波的滤波程序,干扰的信号为60hz的噪声-This is a simple sine wave filtering procedures
The-simulation-led
- 模拟led点阵显示屏,明暗闪烁然后循环显示你所输入的内容-The simulation led to the dot matrix display, bright and dark and then cycle you entered
Number01
- Labview计算器源代码,基于软件的源代码-The the Labview calculator source code, software-based source code
adis16350_all
- This document outlines how to use the Analog Device ADIS16350 High Precision Tri-Axis Inertial Sensor Evaluation Board with the LabVIEW FPGA implementation of the SPI (Serial Peripheral Interface) digital communication protocol. This example reads an
Solar-Charger-Field-Test-1.4.2
- solar charge field program test
TEST
- labview to get square wave from proteus
FCS
- LabVIEW中所有这些能力的最终结果就是极大地提高了效率。许多方面的证据表明相对于传统编程工具效率提高了4到10倍。因此,这可能是导致不将LabVIEW视为一种通用的编程语言的最主要的原因。它是一个更高级的设计工具,从台式机器到嵌入式处理器,再到FPGA-yet few people realize it was originally developed by scientists to study spin and demonstrate that the Earth is rotating
Play-Waveform-
- Play a song using labview
Telescope
- 通过串口将数据上传到PC,使用Labview显示的软件程序。-Using Labview program to desplay datas from the serial port.
使用循环进行数组排序
- 利用labview编写程序: 4、使用循环进行数组排序 要求:可以多次操作,直到点退出按钮。 5. 产生一个3×3的整数随机数数组,随机数要在0到100之间,然后找出数组的鞍点,即该位置上的元素在该行上最大,在该列上最小,也可能没有鞍点。如下图所示: 要求:加上数组元素数设置以及redo按钮重新取值计算 -Labview programming: 4, using a loop array sorting requirements: multiple operati
利用簇模拟汽车控制
- 利用labview编程: 6. 利用簇模拟汽车控制,如右图所示,控制面板可以对显示面板中的参量进行控制。油门控制转速,转速=油门*100,档位控制时速,时速=档位*40,油量随VI运行时间减少。 注意:档位为整数,油量减少速度与档位有关。 7.1 利用随机数发生器仿真一个0到5V的采样信号,每200ms采一个点,共采集50个点,采集完后一次性显示在Waveform Graph上。 7.2 在上题的基础上再增加1路电压信号采集,此路电压信号的范围为5到10V,采样间
定时采 集温度值
- 利用labview编程: 8、将7题中的X轴改为时间轴显示,要求时间轴能真实的反映采样时间。想想为什么与上题的显示结果截然不同? 9、创建头文件,向文件添加采样数据。 内容:创建一个VI,产生头文件,再使用 For 循环定时采 集温度值,并将每次采样时间及温度值以ASCII格式添加到文 件中。 注意:温度值可用随机数+80来生成。-Labview programming: 8, 7 X-axis title to the timeline timeline t
学生信息管理小系统
- 10、一个学生信息管理小系统,可以增加、修改、删除、浏览学生信息,需要将数据保存到文件中,下次可以打开继续浏览 11、使用串口通信的双人聊天程序-10, a student information management of small systems can add, modify, delete, view student information, you need to save the data to a file, you can open the next Continue 1