搜索资源列表
ARM的ADC
- 使用AIN0和AIN1测量两路直流电压，并将结果通过UART0想PC机发送。-compute and the use of two-way con measuring DC voltage, the results through UART0 sent to PC.
6.25-DSP-Pwm-QEP-LED
- DSP2812-PWM-QEP-LED本程序是通过L298P驱动电机，发生两路PWM,通过GPIO口逻辑控制电机转动方向，QEP电路读取电机转速和方向，定时器中断控制LED,非常适合初学者，每一步都写的非常简单，对照着书很容易就看得懂！
STM32f103-ADC-USART.rar
- STM32f103两路ADC数据采集用USART送出,STM32f103 two ADC data acquisition sent by USART
STM32f103-ADC-USART
- STMicroelectronics 32 用ADC模块采集两路信号并通过USART模块送出 * 设置ADC1的常规转换序列包含CH10和CH16(片内温度传感器） * 设置了连续转换模式，并使用DMA传输-STMicroelectronics 32 ADC module with the acquisition of two signals sent through the USART module* set ADC1 conventional conversion sequence
2ADCs_DMA
- 基于CORTEX-M3 内核的STM32两路ADC采集例程 -CORTEX-M3 core-based STM32 two of the ADC acquisition routines
CPLD
- 项目的研究内容是对硅微谐振式加速度计的数据采集电路开展研究工作。硅微谐振式加速度计敏感结构输出的是两路差分的频率信号，因此硅微谐振式加速度计数据采集电路完成的主要任务是测出两路频率信号的差值。测量要求是：实现10ms内对中心谐振频率为20kHz、标度因数为100Hz/g、量程为±50g、分辨率为1mg的硅微谐振式加速度计输出的频率信号的测量，等效测量误差为±1mg。电路的控制核心为单片机，具有串行接口以便将测量结果传送给PC机从而分析、保存测量结果。 按研究内容设计了软硬件。软件采用多周期同
MCP2515_driver_s3c2440based
- 本驱动程序在s3c2440上实现了两路基于SPI的CAN总线控制器。两通道可以并行，并使用外部定义的两个信号量来通知接收任务收到CAN总线帧，并将其存入预先定义的队列中（帧定义在CAN总线控制器驱动程序的头文件中）。CAN总线控制器的中断引脚分别连接到ARM的EINT3和EINT8_23上-The driver s3c2440 achieved a two-way SPI-based CAN bus controller. Two channels can be parallel, and us
TIM1-PWM
- STM32 TIM1 PWM 两路输出，带死区时间-STM32 TIM1 PWM two outputs with dead time
SelectCallTrans
- 使用AVRStudio4编写的ATMega单片机控制2片DDS芯片AD9832同时进行频率输出的程序，通过UART通信接收频率信号的控制字。在实际硬件中将两路信号叠加。-Use AVRStudio4 written ATMega chip control 2 AD9832 DDS chip frequency output of the program at the same time, the frequency signal received via the UART communicati
xs128-capture
- 飞思卡尔xs128 capture ；两路编码器脉冲计数例程-Freescale xs128 capture two encoder pulse counting routines
12C5A60S2-PWM
- 12C5A60S2内部PWM输出，两路。绝对好使，调试通过，内有详细注释，本人详细解读过，担保好使！-12C5A60S2 internal PWM output, two Absolute so that, through debugging, there are detailed notes, I detailed interpretation of the guarantee so!
51_PWM
- 利用51单片机，产生两路互补的PWM波，两个按键调节两路PWM波的频率和脉宽。 程序带有很详细的注释，一看都明白。-51 MCU produce two PWM
AD02
- stc12c5a60s2AD采样，两路，验证，可使用。-AD sampling
pwm
- 简单msp430f149输出两路pwm波示例程序-Simple msp430f149 output two pwm wave sample program
PWM
- 基于mspg2553德州仪器单片机的两路PWM产生程序。亲自调试成功。-Texas Instruments microcontroller based mspg2553 two PWM generator. Personally debugging success.
IDFOOD
- 一具集成了两路H桥的机器人控制板。N场效应管HIP414搭建-set pcb all in one to motor
msp430
- 说明：小路有传感器 p1.0，有车时，两路按照时间交换红绿灯，无车时，大路一直绿灯，小路绿灯时，若 无车立即向小路红灯、大路绿灯转换。-Cross-country road road traffic lights program Descr iption: path with sensors p1.0, have the car, according to the time two-way exchange of traffic lights, no car, the road
code_plcd
- ARM7芯片开发的流量计，可以同时采集两路流量数据，并在液晶屏上显示。-ARM7 chip development of the flow meter, you can simultaneously collect two flow data, and display on the LCD screen.
USB-DUAL-CHANNELPLAYER
- 基于STM32-U盘双通道播放器原理图,可以支持两路同时播放音乐，附原代码，测试过，保证能正常运行。-Based STM32-U disk dual-channel player schematics, can support two simultaneous music-play, attached with source code, fully tested.
ESP8266_NONOS_SDK161128
- ESP8266网络连接，可控制两路开关，带串口AT配置-ESP8266 network connection, can control two switches, with serial AT configuration