搜索资源列表
STM32F103boot
- STM32启动过程解析 1、 通过boot引脚设置可以将中断向量表定位于SRAM区,即起始地址为0x2000000,同 时复位后PC指针位于0x2000000处; 2、 通过boot引脚设置可以将中断向量表定位于FLASH区,即起始地址为0x8000000,同 时复位后PC指针位于0x8000000处; 3、 通过boot引脚设置可以将中断向量表定位于内置Bootloader区,本文不对这种情况做 论述; 而Cortex-M3内核规定,起始地址必须存放堆
STM32-temperature
- STM32在keil环境下通过STM32自身芯片引脚测量温度的例程,使用的开发板为奋斗V3系列的开发板,若果是其他系列的开发板,请注意配置引脚-STM32 STM32 in keil environment through their routines chip pin to measure temperature, using a development board for the struggle V3 Series development board, if the other serie
hello_button
- 通过该实验,您可以了解在MicroBlaze系统中I/O引脚作为通用输入的使用方法,掌握单向输入I/O口的特性,在编程上要掌握如何进行对按键的扫描检测并执行相应动作。-Through the experiment, you can find in the MicroBlaze system using I/O as general input pin, grasp the characteristics of one-way input I/O port, in the programming
STM32F4-Pin
- STM32F4 引脚选择文档,在芯片选型中,非常有用,-STM32F4 Pin Select document
1602-stm32
- stm32上的1602驱动 亲测可用 引脚分配在文件中说明-1602 drivers available on the pro-test stm32
SHT10-stm32
- SHT10数字温湿度传感器的STM32采集程序,更改引脚即可使用。-SHT10 digital temperature and humidity sensor STM32 collection procedures, can be used to change the pin.
static_smg
- 此代码对于初学stm32的GPIO引脚以及静态数码管有很大的帮助-This code stm32 GPIO pin for the beginner as well as static digital great help!!!
gpio
- 适合于做嵌入式开发的初学者,通用IO单元,可以控制外接的流水灯。也可以控制引脚上的电平-Suitable for beginners to do embedded development, general IO unit, you can control an external light water. You can also control the level of the pin
ov7670
- stm32驱动摄像头ov7670源码,已在stm32上验证,不同的stm32板子只要更改引脚即可-stm32 ov7670 camera driver source code, has been validated on stm32, stm32 different pin to the board as long as the changes
CD00220364
- stm32官方器件手册,介绍STM32的功能,引脚,希望对大家有用。-stm32 official device manual describes STM32 features, pin, I hope useful.
V587.ino
- 在单片机上实现五个引脚控制20个灯的轮流闪烁-Five pins on the microcontroller to achieve control 20 lights flashing alternately
PC104--timing-signal
- pc104总线时序信号简介以及各个引脚信号定义,大家可以参考下-pc104 timing signal
EM78P153S_PG005_INT
- EM78P153S中断的应用,本程序以外部中断为例 上电时P50 输出高,在INT 引脚输入下降沿时进外部中断,P50 输出翻转一次。-Application of EM78P153S interrupt this program to external interrupt, for example On electric P50 output is high, the INT pin along the input falls into the external interrupt, fli
TMS320F2812
- 简单的DSPTMS320LF2407A封装引脚图-Simple DSPTMS320LF2407A package pin diagram
RF905_1
- NRF905中文数据手册,包含寄存器设置,引脚说明等-NRF905 Chinese data sheet, include a register set, pin descr iptions
GL827
- GL827,DATESHEET,包括功能引脚说明,封装大小,封装形状,非常适合开发用。-GL827, DATESHEET, including functional pin descr iptions, package size, package shape, very suitable for development use.
mini3216
- 51单片机直接驱动16*32点阵,相当于32个单片机引脚驱动512个LED-51 SCM direct drive 16* 32 dot matrix, equivalent to 32 microcontroller pin drivers 512 LED
DH32
- DH32摇摇棒一个单片机12个引脚直接驱动32个LED,摇晃显示字符-DH32 shook his stick a microcontroller 12 pins to directly drive 32 LED, shaking display characters
nRF4L01_STM32
- 本程序为Stm32F103zet6开发板使用SPI12接口连接常用的nRF24L01无线通信模块进行双工通信的案例,亲测可用,按照引脚定义接线后即可使用。-This program for the Stm32F103zet6 development board using the SPI12 interface to connect the common nRF24L01 wireless communication module for duplex communication case, p
stm32f746_ADC
- 本例介绍如何使用ADC3和DMA,从ADC3到存储器不断传输转换后的数据。 该ADC3配置为连续转换ADC_CHANNEL_8。 每次转换结束时的DMA传输,在循环模式下, 从ADC3 DR转换后的数据注册到uhADCxConvertedValue变量。 该uhADCxConvertedValue读值编码为12位,VREF +基准电压连接 在董事会到VDD(+ 3.3V)时,Vref-之间的参考电压连接在电路板到地面。 要转换的电压读取值,这里是方程适用