搜索资源列表
jtager-0.3.0.tar
- linux下的jtag仿真器程序,可使用在arm7(44b0,4510,2410等)和arm9上面,可以烧写flash 39lv160等,再不用两个系统不停重启了。-the JTAG Emulator procedures, the use of the ARM7 (44b0, 4510,2410) and arm9 above, 39lv160 burning flash, no longer have to keep two systems resumed.
SeekFor GUI Cool(TM) V1[1].0 for S3C44B0x
- CPU:arm S3C44b0 LCD驱动程序 MONO GREY COLOR 包括BOOT LOADER 移植注意FLASH 和SRAM 所在区域-CPU : arm S3C44b0 LCD driver MONO 1,005 COLOR including BOOT LOADER transplant attention FLASH and SRAM region
BiosandBoot
- 这是S3C44B0的BIOS或BOOT LOADER 程序中详细介绍了启动代码和FLASH 的读写 这很容易移植到其它ARM芯片-S3C44B0 This the BIOS or BOOT LOADER detailed procedures for the boot code reader and FLASH This can be easily ported to other ARM chips
NOR和NAND
- 文档详细说明了NOR和NAND闪存各自的特性, 和使用要点。-Documents about the flash memory of both NOR and NAND type.
startup_n
- 经过检验的4510B的BOOT启动代码,是烧到FLASH里面的呦-tested 4510B the BOOT boot code is spread to the inside strove FLASH
UArmJtag2.0
- UArmJtag2.0仿真软件 功能强大、超“硬”的软件仿真器! 博创科技最新发布的ARM调试驱动程序UArmJtag2.0是UArmJtag1.5的升级版本,是继能够成功支持ADS1.2的UArmJtag1.5后的又一重大贡献,UArmJtag2.0可以独立实现FLASH烧写功能,完全替代一般意义上的硬件仿真器,使广大高校师生和科研爱好者从高成本的ARM开发工具中解脱出来! UArmJtag是博创科技自主研发的,超低成本,高性能的ARM仿真调试工具,支持目前市场普遍采用的并口模拟简易仿真器,使
9s12E64IIC
- 是嵌入式处理器,作为IIC的从机,使其与ATMEL24C01的功能相同,同时还包含FLASH的操作代码-is embedded processor, as the IIC from the plane, it ATMEL24C01 with the same functions, and also includes the operation code FLASH
btc5w_boot
- ARM5580A引导程序,采用AMD公司的FLASH,AT29LV160/DT.-ARM5580A guide procedures, using AMD's flash, AT29LV160/DT.
flashpgm2.2.4
- 支持各种FLASH,著名的烧写FLASH的软件,flashpgm-support FLASH, the famous burning FLASH software flashpgm
PWM_VOICE
- 用LPC213X系列的PWM来产生语音。语音数据来源于PC机转换后得到的。最大可以是16位的。 由于是PWM所以输出端口需要低通滤波才能够得到比较干净的声音。 可以经过修改使用LPC2132以上的ARM的D/A来产生。 This project outputs audio on PWM0 using wave samples that are stored in the on-chip Flash ROM. -LPC213X series used to generate th
LPC_ARM_ISP_V2.2.2
- This document can be considered as a supplement to the already existing Application note AN10302 “Using the Philips LPC2000 Flash Utility”, which is provided in the same zip file. The Application note covers the following topics:-This document ca
armFLASH
- 基于s3c2410的arm920T 的flash 编程,希望对广大朋友有帮助。-s3c2410 arm920T the flash programming, and I hope to help the broad masses of friends.
BasicFlash
- IAR编译环境下的AT91SAM7S64芯片的工具演示代码,包括了串口菜单输出和芯片内置flash的烧写功能。-IAR compiler environment of Atmel chip tool demo code, the menu includes a serial port chip output and the built-in flash of burning functions.
AT91RM9200-BasicMmu
- 基于ATMEL AT91RM9200 QFP208的测试源代码,由汇编和C构成,主要用于测试启动时对Flash的读写和相关寄存器设置-ATMEL AT91RM9200 QFP208 based on the test source code, by compiling and C constitute a major test for the commencement of Flash read and write register settings
fs2410_bios
- FS2410板子的bootloader,在ADS中编译出bin文件,烧写到2410 flash 0地址重新上电即可。-Bootloader FS2410 plank of the ADS compile the bin, burning of the flash 0 2,410 addresses can be re-power.
uCOSII_FS44b0x
- 1)通过fs44b0xbios和网口,将upload里的boot.bin烧写到flash 0 地址 见“FS44B0Xbios使用指南”之5 2) 打开57600超级终端 3) 连上串口线和jtag调试头 4)打开FS44B0X开发板电源 5)运行jtag.exe,在SDT下调入 ucosii_demo.axf,运行 6) 在超级终端上有三个任务的运行与退出显示,板子上的三个发光二极管会来回闪烁。 -a) fs44b0xbios and LAN, li will
arm9200Flash
- 基于arm9200的flash编程,完整!希望对大家有用!-arm9200 the flash-based programming, integrity! We hope to useful!
set_flash
- 这是ARM嵌入式开发中闪存的源码,相信对你有帮助-This is the ARM Embedded Development flash source, I believe you have a right to help
flash_MTD_Driver
- 一篇描述如何编写FLASH MTD驱动的介绍性文章。-a descr iption of how to prepare FLASH MTD-driven introductory article.
BootLoaderFlash
- 与Bootloader配合工作的flash烧录程序。-Bootloader tie with the flash replication procedures.