搜索资源列表
tailA
- A simple C program to strobe the LEDsvia Port D. The strobe rate is to be set by adjusting the voltage drop over a potentiometer that is sampled by an ADC.
tailB
- An assembly to strobe the LEDsvia Port D. The strobe rate is to be set by adjusting the voltage drop over a potentiometer that is sampled by an ADC
tailD
- ATmega8 taillight circuitA more complex C program that implements different flashing patterns under the control of both the push buttons and potentiometer. Use your imagination to come up with some novel ideas here. Remember however that more marks a
49-AD_DA_PCF8591
- 此程序通过IIC协议对DAAD芯片操作，读取电位器的电压通过液晶显示，并输出模拟量，用LED亮度渐变指示-Through this program DAAD-chip IIC protocol operation, the voltage through the potentiometer to read LCD display and analog output with LED brightness gradient direction
48-AD_DA_PCF8591
- 此程序通过IIC协议对DAAD芯片操作，读取电位器的电压，并输出模拟量，用LED亮度渐变指示-Through this program DAAD-chip IIC protocol operation, the voltage reading potentiometer and analog output with LED brightness gradient direction
DS1804
- DS1804驱动程序，此芯片是一个数字电位器，可以用单片机调节的电位器-DS1804Driver, the chip is a digital potentiometer MCU, can adjust potentiometer
AD5254
- 通用51单片机，数字电位器AD5254底层驱动-51 SCM digital potentiometer AD5254 driver
ADC
- DQ-STM32开发板试验程序 ADC实验 通过串口输出采样值 通过学习板电位器调节电压 端口分配详见原理图-DQ-the STM32 development board test procedures, experimental ADC serial output sample value by the study board potentiometer to adjust the voltage port assignments refer
ADC01_Data
- LPC2114 ADC Code, It converts Analog to Digital the input as varied by potentiometer on the board.
DualCAN
- 1、该例程为CAN(Normal)例程。 2、使用说明 (1)工程文件路径：例程目录\CAN\CAN(Normal)\MDK-ARM\Project.uvproj。 (2)请使用MDK 4.0以上版本打开,MDK版本过低会导致无法识别工程。 (3)下载调试工具为ULINK。 (4)请将JP1插2-3位置,CAN1L-CAN2L,CAN2H-CAN1H连接。 (5)请将配套LCD模块插上板子CN6。 (6)HEX文件下载到板子后,此时调节可调电位器,LCD
X9584
- 此代码是电子电位器x9584相关代码,此代码使用的控制器为lpc1768！-This code is an electronic potentiometer x9584 related code, this code uses a controller for lpc1768!
digital-
- STM32数字电位器自动调零程序，用以控制数字电位器的大小-STM32 digital potentiometer auto-zeroing procedures
NRF24L01
- 8051控制的NRF24L01无线模块。。主机用PCF8591的AD功能采集电位器和光敏值。- 8051 control NRF24L01 wireless module. The host with AD function and the photosensitive PCF8591 value acquisition potentiometer
MCP4010
- Drive MCP41010 Digital potentiometer with AVR and simulink with Proteus-Drive MCP41010 Digital potentiometer with AVR and simulink with Proteus
TPL0501
- msp320f5529驱动数字电位器tpl0501，已经验证成功。-msp320f5529 drive digital potentiometer tpl0501, has been successfully verified.
MCP410
- STM32，写数字电位器MCP410驱动程序。IO模拟SPI。-STM32, write digital potentiometer MCP410 drivers. IO simulation SPI.
ExampleCode_DAC_AD5141
- 单通道、128/256位、I2C / SPI、非易失性数字电位计AD5141-Single-channel, 128/256, I2C/SPI, nonvolatile digital potentiometer AD5141
STM32_mini_BLDC
- STM32驱动无刷直流电机，方波控制,电位器控制转速，-STM32 drive brushless DC motor, square wave control, speed control potentiometer,