搜索资源列表
ISL60002
- 一个很好的电源稳压器件，温度漂移很小。对电路设计很有帮助-A good power supply regulator device, the temperature drift is very small. Useful for circuit design
shukongdianyuan
- 数控电源设计，内涵电路原理图，设计报告，源程序C代码-Digital power supply design, meaning the circuit schematic, design reports, source C code
tps79901
- 硬件电路设计，电源部分，LDO，专用于开关转线性，专用于对电源纹波要求很高的模拟部分-Hardware circuit design, power supply, LDO, linear transfer switch dedicated, dedicated power supply ripple on the analog part of the demanding
Variable-Auxiliary-Power-Supply-for-low-power-app
- voltage regulator for industrial application
STM32LCD
- 不错的一篇适合初学者的文章，关于STM32中电源PWR管理的程序-Good one for beginners article on the power supply PWR STM32 management program
M8_2400
- ATMEGA8_ LTC2400 6位半表头程序 LTC2400最高测量电压为5.3V，超过5.3V或反接都会烧掉。 模拟部分供电最好经过7815稳压，最高输入电压不宜超过18V。 模拟电路与数字电路分开供电。 不要使用开关电源或PWM升压、降压电路供电 -ATMEGA8_ LTC2400 6 ½ -digit meter program LTC2400 highest measured voltage is 5.3V, 5.3V or rev
ADC_Conti
- DSP的ADC程序开发，对模拟信号采样，然后输出。可以作为数字电源的电压或电流检测信号。-DSP ADC programming, analog signal sampling, then output. Can be used as digital power supply voltage or current signal.
dianyujishu
- 电源技术，关于开关电源的设计以及改进，自己搜集的资料-Power technology, switching power supply design as well as improved information collected
STM32F10xxx
- STM32F10xxx硬件开发使用入门,硬件的设计，包括电源的配置，Jtag设置、复位电路-The STM32F10xxx hardware development started, hardware design, including the configuration of the power supply, Jtag set reset circuit. .
MC323
- MG323 模块工作电压3.3V-4.2V，推荐工作电压 3.8V，不建议用边缘值电压， 电压波动会造成模块工作不稳定。推荐使用2A以上的 LDO或开关电源。 -MG323 module work voltage 3.3V-4.2V, the Recommended Operating voltage 3.8V, is not recommended with the edge of the value of the voltage, the voltage fluctuation wi
lcd_SMS0801B
- MSP430F149，IAR环境下，段式液晶SMS0801B的显示驱动程序，可以直接显示浮点数。该液晶工作电流约为20uA左右，十分适合做电源用。-MSP430F149, IAR environment, SMS0801B Segment LCD display program can display floating point number. The LCD operating current is about 20uA , very suitable for power supply.
STM32F103-SPI-W25X16-W25Q16
- 1、该例程为STM32串口1测试例程。 2、使用说明 (1)工程文件路径：.\USER\STM32-DEMO.uvprojj。 (2)请使用MDK 4.0以上版本打开,MDK版本过低会导致无法识别工程。 (3)下载调试工具为JLINK。 (4)请将串口线(两头皆为母的交叉串口线)插在板子COM1口上,并打开超级终端或串口助手，配置波特率115200，8位，一个停止位，无校验位。 (5)插上DC-5V电源、插上JLINKV8后，点击MDK工具栏中的LOAD
gaoliangLEDdianludaquab
- LED电源电路大多是由开关电源电路+反馈电路这样的形式构成，反馈电路从负载处取样后对开关电路进行脉冲的占空比调整或频率调整，以达到控制开关电路输出的目的- LED power supply circuit are caused by switching power supply circuit+ feedback circuit constituted in such a way, the feedback from the load circuit after the switch cir
Powe
- protel嵌入式系统 数控液晶显示可调电源-protel Embedded System CNC LCD adjustable power supply
program2
- 这是我的ARM7课程设计，做的是线性可调直流电源，主要是AD和DA的操作可以提供借鉴。-This is my ARM7 curriculum design, do a linear adjustable DC power supply, mainly AD and DA operations can provide a reference.
code.lpc23xx.peripherals.iar
- 接通电源后开发板左下角电源指示灯亮，表示电源工作正常。这里是LPC2468开发板全部例程,keil开发环境，希望对新人有帮助。-After turning on the power development board of the lower left corner of the power indicator light, said the power supply works. Here is the LPC2468 development board all the routines, a
SourceCode_OfflineUPS_220V
- 基于单片机的逆变电源和细分电源的设计，在工业运用中十分广泛。-MCU power inverter power supply design and segmentation based on a wide range of industrial applications.
led
- 在移动电源项目中使用，四只LED灯根据电量闪烁及常亮-Used in mobile power supply project ，Four LED lamp according to the power and constant light flashing
MSP430iar
- This feature is available only on the SST39VF800Q. This pin functions as power supply pin for input/output buffers. It should be tied to VDD(2.7-3.6V) in a 3.0V-only system. It should be tied to a 5.0V±10 (4.5-5.5V) power supply in a mixed vo
PMP4419-PCB-Layout
- 220V24V开关电源，3路输出，24V，正负15V，电路板图-220V24V switching power supply, 3 outputs, 24V, ± 15V, the circuit board diagram