搜索资源列表
AnteeoBee_20060218
- his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run \"make\" from the console in echomaster and ech
ssc_sent_spi
- 在ads1.2上运行，适合高速的数据通信。数据可以以50Mbit/s的速度由ssc口进入，经过处理、过滤后由SPI口输出。其中使用了快速强制中断，处理效率很高。注意：本工程是汇编级程序，可读性差，但效率极高。-run in ads1.2 suitable for high-speed data communications. Data can be 50 Mbit / s rate from ssc I entered, processed, filtered output from SPI m
basic.zip
- 飞思卡尔MPC5554 target To build your project, use the menu Project > Make or press F7. This will build the selected target.,This is release 1.00 of the eTPU function set1. The package contains the binary image of the eTPU code for the CPU to use,
FRAM
- 基于STM32处理器SPI接口的FRAM存储器程序，项目中用到的，原创，读写等基本函数均已写好，可直接使用-STM32 processor SPI interface based on FRAM memory process, the project used, original, read and write basic functions have been written, can be used directly
userial-firmware-v1.6
- userial is an Free project building an USB to I2C/SPI/GPIO bridge, using the Atmel AT90USB647 chip. Hardware and Software are released under an Open Source licence. It supports the following interfaces: * USB interface (serial emulation) *
spi7219fors3c2440
- 自己写的 基于arm s3c2440 max7219的现实程序，用软件模拟spi协议，开发板用的是友善之臂mini2440，ads1.2开发，包含所有项目文件，保证好用，给有需要的朋友，-Write your own arm s3c2440 max7219-based reality program, using software simulation spi protocol development board using a friendliness arm mini2440, ads1.2
SDcard
- 无系统 STM32 SD卡源码！KEIL工程。 -No system STM32 SD Card source! KEIL project.
basic-sd-spi-project-at91sam7x-ek-keil
- JIYU AT91SAM7X256的SD接口卡的驱动代码实现-JIYU AT91SAM7X256 the SD interface card driver code to achieve
basic-serialflash-project-at91sam7x-ek-keil
- The Basic Serialflash project will help new users get familiar with SPI interface on Atmel s AT91 family of microcontrollers. This project gives you an AT26 serial firmware dataflash programming code so that can help develop your own SPI dev
basic-sd-spi-project-at91sam7x-ek
- at91sam7x256之spi，读写sd卡-at91sam7x256 the spi, sd card reader
basic-sd-spi-project-at91sam7s-ek
- Data loader to a MicroSD memory using an ATMEL ARM AT91SAM7S Microcontroller, using IAR Systems compiler.
basic-sd-spi-project
- it is source code for at91sam9260 for SD SPI -it is source code for at91sam9260 for SD SPI
getting-started-project-at91sam9261-ek
- AT91SAM9261-EK各模块程序PIO，SPI，UART等-the test code of AT91SAM9261-EK boards
RTX_Blinky
- this project is for using spi port in NXP philips arm microcontrollers
SDkaSource
- SD卡的SPI读写程序，内含SPI总线时序函数、SD卡的读写函数，可直接嵌入到UC/OS操作系统中进行调用,采用.c和.h文件进行分装，可直接嵌入到项目或操作系统中，支持51单片机、STM32、ARM7等单片机，500M主屏以上的处理器请对SPI时序进行修改。-SD card SPI read and write procedures containing SPI bus timing function, SD card reader function, can be directly embe
STM32F10X_DEMO_3.5.0
- 基于STMF103ZET6移植最新固件库3.5.0版本，是一个完整的工程，并详细中文注释，包括按键，TFTLCD液晶显示、SPI.USART.I2C,FSMC,DMA,DAC,ADC等常用外设模块文件，完全调试测试通过，可以直接使用哦。-Transplantation based on the latest firmware library STMF103ZET6 version 3.5.0, is a complete project, and detailed notes in Chines
SPI
- Use SPI for ARM (lpc2138) in Keil And Proteus Project
STM32F103-SPI-W25X16-W25Q16
- 1、该例程为STM32串口1测试例程。 2、使用说明 (1)工程文件路径：.\USER\STM32-DEMO.uvprojj。 (2)请使用MDK 4.0以上版本打开,MDK版本过低会导致无法识别工程。 (3)下载调试工具为JLINK。 (4)请将串口线(两头皆为母的交叉串口线)插在板子COM1口上,并打开超级终端或串口助手，配置波特率115200，8位，一个停止位，无校验位。 (5)插上DC-5V电源、插上JLINKV8后，点击MDK工具栏中的LOAD
LM3033-SPI
- STM32 模拟SPI控制LM3033显示屏源码。项目中已实际应用。封装了外部调用接口，类似项目可以直接移植使用。-STM32 simulation of SPI control LM3033 display source code. The project has practical application. Package the external call interface, similar projects can be directly transplanted to use.
basic-sd-spi-project-at91sam7s-ek
- The Basic-sd-spi-project will help you to get familiar with sdmmc_spi interface on AT91SAM microcontrollers. It can also help you to get familiar with the SD operation flow which can be used for fast implementation of your own sd drivers and other