搜索资源列表
watchdog
- 在系统运行以后也就启动了看门狗的计数器，看门狗就开始自动计数，如果到了一定的时间还不去清看门狗，那么看门狗计数器就会溢出从而引起看门狗中断，造成系统复位。所以在使用有看门狗的芯片时要注意清看门狗。-Watchdog implication
watchdog
- 这是一个看门狗程序，大家可以下载下来看看，是个很好的程序。-this is a application-WATCH DOG,i think that many people will want to download it.
6watchdog
- 基于MINI2440的 看门狗实验源码+启动代码 下载后可以直接运行-Based on experimental MINI2440 watchdog download source+ startup code can run! !
watchdog-5.6
- 非常实用的看门狗程序，直接针对硬件底层，为系统的稳定保驾护航，特别对底层开发人员有使用价值。-failed to translate
wdog
- i.mx27看门狗测试源码 开发板自带源码-i.mx27 watchdog test source development board comes with source code
S3C2410_WatchDog
- 基于S3C2410的看门狗例程，里面具有源代码以及项目文件。-Based on S3C2410 watchdog routines, which have the source code and project files.
watchdog
- 嵌入式Linux下的看门狗程序 在JX2410下成功运行。-Embedded Linux Watchdog program under the JX2410 ran successfully.
watchdog
- 是s3c2440开发板的看门狗测试程序，觉得还不错，值得参考-Development board of the watchdog is s3c2440 test procedure, that is not bad, it is also useful
6-watchdog
- mini2440裸机学习篇之看门狗！ 相信对裸机学习的朋友有帮助。-learning is the watchdog mini2440 bare metal! Learning on the bare metal friends that help.
watchdogtimer
- 北京三恒星科技公司的6410开发板测试代码中看门狗部分代码-Beijing three star technology companies in the 6410 development board watchdog part of the code test code
watchdog1
- 该文件为ARM11下的看门狗源程序及框架图，为方便同行共同开发特此上传-This file is the source code and ARM11 watchdog under the framework map, to facilitate the joint development hereby peer upload
watchdog_test
- s3c2410控制看门狗，使用优龙fs2410开发板。-s3c2410 control the watchdog，using ucdragon board。
watchdog1
- s3c2440 看门狗实验 s3c2440 看门狗实验-s3c2440 看门狗实验
demo_test6410_sys
- s3c6410demo功能演示：要求分别能对LED，BUTTON，ADC，PWM蜂鸣器，定时器，看门狗，RTC等模块进行功能测试。-s3c6410demo function demonstrating the s3c6410demo function demo: requirements for functional testing of LEDs, the BUTTON, the ADC, PWM buzzer, timer, Watchdog, RTC and other modules.
Armplat_WTdog
- ARM Linux gec2440开发板看门狗报警中断-The ARM Linux gec2440 development board watchdog alarm interrupt
watchdog
- 基于ARM的看门狗程序设计，适用于刚接触ARM的人-ARM-based watchdog program design, suitable for new to ARM
watchdog.tar
- 一个看门狗进程的代码。打开看门狗后进行喂狗，喂5次后停止喂狗，看开发板会不会重启。-A watchdog daemon code. Open watchdog and then feed the dog, fed five times then stop feeding the dog, see whether will the development board restart.
2th
- 最简单的bootloader的编写步骤： 1. 初始化硬件：关看门狗、设置时钟、设置SDRAM、初始化NAND FLASH 2. 如果bootloader比较大，要把它重定位到SDRAM 3. 把内核从NAND FLASH读到SDRAM 4. 设置"要传给内核的参数" 5. 跳转执行内核 -The easiest the bootloader preparation steps: 1. Initializes the hardware: Off watchdog, set
watchdog
- “看门狗”程序及仿真图基于LPC2138-" Watchdog" program and simulation diagram based on the LPC2138
watchdog
- 一些看门狗与串口控制的测试内容代码只能做到beeon 不能做beeo-Some watchdog test content and serial control code can do beeon not do beeoff