搜索资源列表
2410LED
- 2410开发板在ADS下测试LED的程序 运行步骤： 1 打开led.mcp工程文件 2 运行 3 观察开发板上的跑马灯闪烁 文件说明： init.s 开发板初始化文件 Main.c 中断实验主程序文件-2410 ADS development board in the LED under test running steps : an open led.mcp engineering documents two running three observation o
UCOS2.71souce
- 含代码UCOS_II测试程序说明有详细过程说明 测试步骤 1> 开发板上电 2> 运行串口监视软件,波特率115200,8N1 3> 运行测试程序 4> 在串口监视软件中显示OSRunning后，最右侧的LED灯开始闪烁， 间隔为1秒。同时每隔2秒可以在监视窗口中看到当前CPU利用率。 按下某个键后，会在监视窗口中看到诸如“msg = x”的信息。-containing code UCOS_II test a detailed de
uCLinuxLEDblink
- 在英培特试验箱上实现LED灯循环闪烁功能的源码和Image文件-tissue culture chamber of the British achieving blinking LED lights cycle function of source documents and Image
fpga
- 基于PXA270-S linux的FPGA实现。 向LED_CONTROL写入n即得到n*0.1S的延时，LED闪烁的快慢程度发生变化。
menjin.rar
- 以S3C2410为目标板，利用串口读取读卡器的磁卡信息来控制LED的闪烁，用QT做的显示界面，模拟门禁控制,S3C2410 for the target board to the use of serial magnetic card reader to read the information to control the blinking LED, QT to do with the display interface, simulation of access control
miaobiao
- 在LCD屏幕上显示秒表计时，并利用按键控制秒表的开始与暂停及清零。同时LED灯呈跑马灯闪烁-Displayed on the LCD screen stopwatch timer, and stopwatch using buttons control the start and pause and clear. LED lights were also flashing marquees
gpio-test
- 针对嵌入式开发板上面的LED灯进行编程控制，实现LED灯的闪烁，开光。需要用到内核态函数，可以参考修改，实现各式各样的显示要求！-Development board for embedded LED lights above program control, the realization of LED flashing lights, the light. Needed core state function, can be edited to achieve a wide range of
exp2
- EPSON C33209嵌入式平台 实现发光二极管闪烁-EPSON C33209 embedded platform LED flashes
LEDBLINK
- 万龙开发板ARM44B0 发光管轮流闪烁例程-WangLong Development Board ARM44B0 LED flashing routine
LINUX_ARM
- sam7x256的led闪烁工程 sam7x256的led闪烁工程 -sam7x256' s led the led flashing flashing project sam7x256 the led flashes engineering works sam7x256 the led flashes works sam7x256
watchdog
- 正常时流水灯循环闪烁,复位时四个LED全亮,当不及时喂狗即产生复位信号,流水灯闪烁会被打断.-Normal water cycle flashing lights, reset all four LED lights, feed the dog that is not timely when a reset signal, flashing light water will be interrupted.
zd
- 1.实现中断嵌套 2.使用定时器4，采用中断方法实现RUN LED闪烁，频率为5hz， 3.使用外部中断0，控制RUN LED是否闪烁。-1. Achieve interrupt nested 2. Use timer 4, the interrupt method RUN LED flash, frequency for 5 hz, 3. Use external interruption 0, control whether RUN LED twinkle.
control-led-by-keys
- 以s3c2440芯片为核心，通过矩阵键盘按键来控制LED闪烁，属于裸机开发。-control led by keys
armplat_timer0_LED
- S3C2440中断定时器用，定时器控制LED闪烁-The S3C2440 interrupt timer, the timer controls the LED blinks
TQ2440
- 基于天嵌TQ2440开发版的裸机代码源码包括点亮LED让LED闪烁还有按键程序（利用断或查询的方式），串口的源代码，可直接烧进开发板运行-The day embedded TQ2440 Developer Edition bare metal code source-based lit LED LED flashes also key program (off or query), the serial port of the source code, can be directly burne
LEDBLINK
- 在S3C44B0上实现LED的闪烁，学习发光管轮流闪烁的程序。-LED flashes in S3C44B0 learning program LED flashes.
ledcycle
- ok6410开发板裸机led跑马灯源码，控制led循环闪烁！-ok6410 development board the bare metal led Marquee source, control led circulating flashing!
Led_test
- S3C44B0LED测试，实现LED闪烁的功能。-S3C44B0LED test, implement LED blinking function.
ARM9
- 基于ARM9的倒计时秒表，用QT绘制界面，倒计时为零LED闪烁，有加减计时，暂停，启动，复位，单片机复位等功能-ARM9-based countdown stopwatch with QT drawing interface, the countdown to zero LED flashes, there is plus or minus timing, pause, start, reset, the microcontroller reset function
LED灯的闪烁
- 点亮LED 用lpc两千系列进行点亮，涉及仿真内容(Lighting the LED with the LPC 2000 series of lighting, involving simulation content)