搜索资源列表
sanjiaoboandjuchi
- 51+DAC0832产生三角波和锯齿波，汇编程序-A triangle wave and sawtooth 51+DAC0832 assembler
dpj
- STC89C52单片机与DAC0832结合产生方波、正玄波、三角波、方波、锯齿波、梯形波-STC89C52 microcontroller and the DAC0832 to produce a square wave, sine wave, triangle wave, square wave, sawtooth wave, trapezoidal wave
DA
- 汇编语言C51定时器8255流水灯、按键输入，DA/AD三角波，正弦波-51
xinhaofashengqi
- 产生方波，三角波，矩形波，使用51单片机，波形发生器，c程序-Produce a square wave, triangle wave, square wave, using 51 microcontroller, waveform generator, c program
lu_DA---2
- 基于学生开发板的DA功能的编程，通过DA转换实现，方波，三角波，正弦波和其他波形，可通过物理按键实现多种功能-DA features programming based on the students' development board, realized through the DA converter, square wave, triangle wave, sine wave and waveform can be achieved through the physical bu
project45
- 5个开关K1-K5（从上到下），分别对应正弦波、方波、三角波、梯形波、锯齿波，按一下其中一个开关，则选择出所要产生的波形。（哈工大单片机大作业内附proteus原理图）-5 switch K1-K5 (top to bottom), corresponding to the sine wave, square wave, triangle wave, trapezoidal wave, sawtooth, click one of the switch, and then select the
wave
- 单片机程序，AT89C51单片机产生正弦波，方波和三角波-Microcontroller program, AT89C51 microcontroller sine, square and triangle wave
signal-generator-
- 信号发生器 关键词：ATmega16、LCD12864、ICC AVR、AVR Studio、Proteus、AD5310、UA741、SPI 用ATmega16单片机控制AD5310产生正弦波、方波、锯齿波、三角波信号。通过按键可以切换信号类型、改变信号幅度和频率。 -Signal generator Keywords: ATmega16, LCD12864 ICC AVR, AVR Studio Proteus, AD5310, UA741, SPI, ATmega16
Function-signal-generator
- 这是一个用单片机做的函数信号发生器，能发送三角波、锯齿波、方波并且可调频率，通过外部按键调节。-This is a microcontroller do function signal generator, can send a triangle wave, sawtooth wave, square wave and adjustable frequency regulation through external buttons.
zonghe
- 波形（正弦波、方波、三角波）检测并显示，及波形的判定和相关参数的测量。-Detect and display waveforms (sine wave, square wave, triangle wave), and waveform determination and measurement of relevant parameters.
sanjiaobo
- 凌阳单片机，凌阳液晶显示模块，单片机生成三角波在液晶显示程序。-Sunplus MCU Sunplus LCD module microcontroller generates a triangular wave in the liquid crystal display.
19-PCF8591-AD-change
- 将p1.0口模拟时钟口将p1.3口模拟数据口实现DA转换可以输出三角波，锯齿波，正弦波等-P1.0 port analog clock port p1.3 port analog data port DA converter can output a triangle wave, sawtooth, sine
20-PCF8591-DA-change
- 数模转换可以将数字量转换为模拟量从而输出三角波，锯齿波，正弦波等-Digital-to-analog conversion to digital conversion for analog output triangle wave, sawtooth, sine wave
bxfsq
- 波形发生器的总体设计思想编程，主要就方波、三角波等产生进行设计。-The overall design philosophy of the waveform generator programming, mainly on the square wave, triangle wave design.
123
- stm32使用DMA模块产生三角波和正弦波的方法-stm32 use DMA module generates a triangle wave and sine wave
sin-DDS
- 做DDS时需要用到如三角波，正弦波之类波形的采样数据，这个函数可以产生任意采样点数和任意幅值的正弦波数据点。由该函数产生的数据很容易的转化为.mif文件-Do DDS when needed, such as triangular wave, sine wave like waveform of sampled data, this function can be generated in any sampling points and optionally the amplitude of t
DAC0832
- AVR单片机mega16控制DAC0832输出三角波-The AVR controlled DAC0832 output triangle wave
waveshaper
- 用单片机AT89C51完成的波形发生器，用DAC0832完成数模转换。可以产生三角波、方波、正弦波。-With microcontroller AT89C51 complete waveform generator, the DAC0832 digital-to-analog conversion. Can generate the triangular wave, square wave, sine wave.
2
- 程序功能为基于10位的高精度DAC数模转换器，实现频率比较高的周期周期性信号输出，分别实现锯齿波和三角波输出，通过控制插入的软件延时可以达到调节输出信号频率的目的。-Program function is based on 10-bit precision DAC digital-to-analog converter, to achieve a relatively high frequency periodic periodic signal output, respectively, to
3
- 本程序实现锯齿波、方波、三角波函数信号输出，实现原理基本一致，输出数字量间隔一定时间增加1，256个时间间隔实现周期性输出，通过调节时间间隔可以改变输出信号的周期长短，通过放大器可以实现信号幅度的调整。-The program to achieve sawtooth, square, triangle wave function signal output to achieve basically the same principle, the digital output increase i