搜索资源列表
shiyan2
- 开发环境:unSP IDE 2.0.0 实验目的:通过本实验熟悉SunPlus SPCE061A单片机的I/O,定时器的使用方法。中断系统的 使用。熟悉IDE开发环境的使用。 0 实验设备:装有WINDOWS操作系统以及SunPlus IDE仿真开发环境的PC机一台; ì’nSP™ 十六位单片机实验板及扩展板。 实验原理:通过键盘扫描获得键值后分别控制二极管的亮灭;使用定时器产生不同的显示模 式。 实验步骤: 1).连接PC机与SunPlus061A仿
lpc2138_timer0_interrupt
- lpc2138定时器0的中断处理过程.中断的初始化和 处理过程-LPC2138 TIMER0 interrup source code.THE initionlize and interrup handle.
sy2
- 外部中断技术的基本使用方法和中断处理程序的编程方法-The basic use of external interrupts and interrupt handling techniques programing method
cc2530_uart
- cc2530与pc通信,中断处理接收数据。-cc2530 with pc communication, interrupt handling received data.
INTERMIT1
- 用单次脉冲申请中断,在中断处理程序中对输出信号进行翻转。-Applications with a single pulse interrupt, the interrupt handler flip the output signal.
STM32
- 基于STM32单片机将RS232串口采集的数据转换为CAN总线数据输出,程序中以采集电罗经数据为例,包括了电罗经数据的过滤、串口中断处理、CAN中断处理等程序模块。-STM32 microcontroller based data acquisition converts RS232 serial CAN bus data output, a program to collect electronic compass data, for example, includes a filter gy
zzkz2000
- 基于128A屏幕的程序,芯片是C8051F060,包括外部中断处理,编码器的读取-128A based on the program screen, chip C8051F060, including external interrupt processing, reads the encoder
STM32_Wiegand_TestOK
- 基于stm32的韦根通信协议,使用io中断处理,可以切换韦根26和韦根32收发,经过测试比较稳定-Stm32 Wiegand based communication protocol that uses io interrupt handling, you can switch Wiegand Wiegand 26 and 32 receive, tested relatively stable
GPIOpolling
- STM32按键程序。PB0连接到key1,PB0配置为线中断模式,key1按下时,进入线中断处理函数,LED1状态取反。-STM32 key procedures. PB0 connected to key1, PB0 configured for line break mode, press key1 into line interrupt handler, LED1 status negated.
ExtiKey
- 基于STM32,PB0连接到key1,PB0配置为线中断模式,key1按下时,进入线中断处理函数,LED1状态取反。-PB0 connected to key1, PB0 configured for line break mode, press key1 into line interrupt handler LED1 status negated.
interrupt
- 采用C语言编程,在JX44BOX教学实验箱进行中断处理的实验。-采用C语言编程,在JX44BOX教学实验箱进行中断处理的实验。 Using C language programming, in the JX44BOX teaching experiment box for interrupt processing experiments.
stepmotor
- 基于MSP430单片机步进电机驱动函数,中断处理-MSP430 microcontroller-based stepper motor drive function, interrupt handling
LM83
- 本程序用于通过SMBus总线接口对LM83温度传感器的工作模式设定,中断处理程序用于对温度超限的处理。 只开启远程温度D1+的监控,高温标志80摄氏度,严重越限温度为100摄氏度 51单片机P1.0和P1.1用于软件模拟Smbus总线时序 Smbus总线命令、数据读写程序,保持时钟线常态为低,数据线常态为高-This procedure is used by the SMBus interface mode LM83 temperature sensor setting, the i
new_instruct
- 教你学会单片机开发板的定时器的中断处理程序,-Teaches you how to microcontroller development board timer interrupt handler,
map430g2553
- 利用MSP430G2553产生正弦波,含有两个中断处理,三个计数器-Use MSP430G2553 produce sine, contain two interrupt handling, three counters
infrared_decode
- 红外解码实现对红外信号实现中断处理,并处理解码后在上位机中显示对接数据。-Infrared decoding to achieve the realization of the infrared signal processing, and processing and decoding in the host computer display docking data.
interrupt
- s3c2440 中断处理程序,按键蜂鸣器响-S3c2440 interrupt handling procedures, buzzer button
EXTI
- 实现外部中断,处理中断事件。。。。。。。。。(peripheral interrupt)
stm8的SPI初始化处理部分
- SPi初始化,验证可正常使用,没有中断,DMA(SPi initialization, validation can be used normally)
基于DSP中断工作方法的音频滤波代码
- 设计基于DSP中断工作方式的语音采集-滤波-回放系统,要求: 1.输入为双声道立体声音频,用48kHz的采样率采集音频。 2.将音频信号经36阶截止频率10kHz的低通滤波处理后,再进行回放。 3.要求采用音频接收、播放双中断工作方法。