搜索资源列表
WL024_ADC0832数字电压表LED显示
- 控制ADC0832做数据采集，并用数码管显示出来，搞测控的朋友可以-control data acquisition, control and digital display and control of engaging friends can play
GvgLedTest
- 建立在AVR基础上的测试LED数码管电压表-established on the basis of the test tube voltage LED digital Table
voltagemeter.rar
- 简易数字电压表 测量0~5V电压，数码管显示，使用STC12C5410AD单片机,Simple digital voltage meter 0 ~ 5V voltage measurement, digital display, the use of single-chip is STC12C5410AD
ad0809.rar
- 测量电压值，将模拟变成数字，通过数码管显示,Measured voltage value, the analog into digital, digital display
atmega8-6ADC
- AVR系列ATmega8单片机制作的6路ADC同时检测6个电压程序，检测结果使用数码管，使用ICCAVR编写，附Proteus仿真文件。-AVR Series ATmega8 microcontroller produced use 6-channel simultaneous detection of six voltage ADC program, test results of the use of digital control, the use of ICCAVR write, wit
AD
- STC单片机AD转换程序并能在数码管上显示，采样电压为0-10V转化成0-100或0-150在数码管上输出-STC Single-chip AD conversion
dianya
- 用C实现数字电压电流表：1、由外部输入直流电压电流，电压范围20V，电流范围1A； 2、电压/电流通过开关切换； 3、显示：数码管显示电压值/电流值，精度0.01。 -Implementation using digital voltage ammeter C: 1, by the external input DC voltage and current, voltage range of 20V, the current scope of 1A 2, voltage/curre
cccc
- 简易数字电压表可以测量0-5V范围的8路电压值，并在4位LED数码管上轮流显示或单路选择显示。-Simple digital voltage meter can measure the range of 0-5V Voltage road 8, and 4 digital tube LED display on a rotational basis or choose to display a single road.
szdyb
- 数字电压表,可模拟进行电压测量,用数码管显示电压值,有图和程序-Digital voltage meter, can be simulated for voltage measurement, digital display voltage value, a plan and procedures
51-single-chip-proseor
- 基于51单片机的温度和电压采集与循环显示的控制程序，其中温度传感器为LMA95，采用I2C总线传输，显示器为8段LED数码管-51 single-chip-based temperature and voltage of the cycle of acquisition and display of the control procedures, including temperature sensors for LMA95, using I2C bus transmission, displa
adc0809vhdk
- 对adc0809的控制及数码管输出，能直观的看见电压数-Of adc0809 control and digital control output voltage can see a number of intuitive
test
- 用51单片机实现数字电压表，使用4位数码管作为显示器，测量范围为0-5VDC，-aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
AD_count_countdown
- 设置3个功能键：当某一功能键被按下后，进入相应的功能模式。3个功能有： 1）8路数据采集功能：通过调节可变电阻实现0-5V的电压输出作为8路输入信号使用，每路信号用2位LED显示采集的结果。报警：任意一路超过某一门限（可自己设定）时，发出报警（声音+灯闪烁，并通过灯指示是哪一路报警），同时停止采集。2）计数功能：利用计数功能键，实现每按一次按键，LED显示加1，从0-99计数。3）秒表功能：只用一个键控制。按下一个按键后时钟启动，从零开始计时，计时间隔0.01秒，再按一次后停止。再按一次后清
DC
- PIC单片机直流电压采样并用数码管显示,挺好用的-PIC Microcontroller DC voltage sampling and digital LED display, quite good use of
AD
- 用STC的AD功能实现电压（量程为5V）测量，并用数码管显示-With the STC function realization of the AD voltage (range is 5V) measurements, and use digital tube display
ADC0804_fangzhen
- ADC0804数字电压表仿真，四位数码管显示，C源程序，keil编译通过，附上protus仿真源文件，打包下载。-ADC0804 digital voltmeter simulation, four digital tube display, C source code, keil compiler passed, accompanied by protus simulation source files, package download.
voltmeter2052AD(OK)
- 基于12c2052ad 的数码管显示电压表-Based 12c2052ad the digital display voltmeter
极简电压表
- 采用stc15 mcu的极简电压表。利用其内部基准电压为基准测量，并驱动3位共阴极LED数码管显示。(A minimalist voltmeter using the stc15 mcu. The internal reference voltage is used as the reference to measure and drive the 3 bit common cathode LED digital tube display.)
三位数码管显示0~24V电压SN8P2711
- 通过SN8P2711的AD口采集电压,在三位数码管上显示出来,可测量0~24V电压,误差范围在+-0.5V(The voltage is collected through the AD port of SN8P2711 and displayed on three digital tubes. The voltage can be measured from 0 to 24V. The error range is +0.5V)
【实验28】AD数码管显示电压
- PIC16F877开发板例程————AD数码管显示电压(PIC16F788 development board program --- AD digital tube display voltage)