搜索资源列表
MSP430 数据采集
- 利用MSP430 单片机的一般 I/O口进行的数字量的采集 利用A/D采集通道实现模拟量到数字量的转化-use of the general I / O port for the digital collection using A / D channel analog output of the digital conversion
EELOM1
- 采用PIC16F877A单片机,A/D模拟量采集,LED显示,E2ROM存储,可断电保持显示数据,已硬件调示通过.供大家参考.-used PIC16F877A microcontroller, A / D analog acquisition, LED display, E2ROM storage, power outages can maintain data show, has said through the transfer hardware. for your reference.
AAA1-87g1
- PIC16F74单片机A/D10位模拟量采集,12864LCD汉显,显示4位数带小数点-PIC16F74 microcontroller A/D10-analog acquisition, 12864LCD Han obviously, 4 shows the median with a decimal point
cx1
- PIC16F873单片机A/D转换程序,可用于模拟量采集
modbus-51-src
- 汇编,C 源码 用STC89C58单片机做的数据采集和控制,12位AD转换使用TLC2543,通讯协议采用MODBUS(RTU),通过拨码开关改变从机地址,支持模拟量或数字量的读写。(4路模拟量输入、6路开关量输出(继电器输出)、8路开关量输入)开发环境:KEIK 7.06 (2006-7-5,C-C++,61KB,17次) -Microcontroller to do with STC89C58 data acquisition and control, use 12-bit AD
MSP430Data_Acq
- 本例中含有MSP430单片机实现的数据采集系统的电路图及C源程序,软件主要包括模拟量采集模块、数字量采集模块、串口通信模块和主处理模块。-In this case contains MSP430 MCU Data Acquisition System circuit diagram and C source code, software mainly includes analog acquisition module, digital volume acquisition module, se
duolushujucaijiyuchuanshu
- 数据采集系统作为沟通模拟域与数字域的必不可少的桥梁有着非常重要的作用。本文介绍的重点是数据采集系统。数据采集与通信控制采用了模块化的设计,数据采集与通信控制采用了单片机8051来实现,硬件部分是以单片机为核心,还包括模-数转换模块,显示模块,和串行接口部分,还有一些简单的外围电路。8路被测电压通过通用ADC0809模-数转换,实现对采集到的数据进行模拟量到数字量的转换,由单片机对数据进行处理,用LCD显示模块来显示所采集的结果,并将数据通过串行口传输到PC机上,MCU与 PC机间的电平匹配采用M
ai1
- MSP430 模拟量采集实现程序,带外部的多路选择开关控制-MSP430 analog acquisition to achieve program, with an external multiplexer switch control
ADCPWM
- 模拟量采集和3路脉宽调制输出(OCR1A/OCR1B&OCR2)综合程序/晶振4MHZ-ANALOG CONVERTER AND THREE PWM OUTPUT (OCR1A/OCR1B&OCR2),CRYSTAL:4MHZ
430Pro
- msp430单片机处理程序,单片机初始化,模拟量采集,滤波,串口通讯-msp430program
0832_LCD
- 基于atmega16单片机应用模数转换芯片0832进行模拟量采集。可以进行通道选择,程序于8Mhz晶振下调试通过。-SCM applications based on atmega16 ADC chip 0832 for analog capture. Can channel selection, the program to debug through the crystal in 8Mhz.
voit
- 本例利用ADC0809 的A/D 转换原理,将被测的多路模拟量转换成数字量,并 用数字方式显示测量结果。本系统以单片机AT89C52 为系统的控制核心,结合A/D 转换 芯片ADC0809 设计一个多路电压采集系统,其中A/D 转换结果经过AT89C52 处理,最后 通过数码管显示相应的数值。本系统通过一个按键可以选择8 路0-5V 之间的直流电压 值进行测量,并在四位数码管上显示相应的数值。读数据准确,测量方便。-In this case the use of ADC0809
201010128448748
- PCI-9101数据采集,以VB对数字量和模拟量之间的转换,8道数据的采集做了简单的编程,希望对做工程类的朋友有所帮助,本人水平有限如有错误敬请见谅! -PCI-9101 data acquisition to VB and analog to digital conversion between 8 to do a simple data acquisition programming, want to do engineering friends help, I is limited, if
main
- 基于Stm32的CAN总线的ADC模拟量采集-Stm32 Can ADC
danpianji
- 单片机液晶显示翻页菜单,模拟量采集并转换成数字量,蜂鸣器报警及数字计时-SCM LCD flip menu, analog capture and conversion into digital, the buzzer alarm, and digital timing
Base_on_ARM7_LPC2136
- 这是一个自己开发的产品-电子膨胀阀驱动器,单片机为ARM7,有步进电机驱动模块,模拟量采集处理,数字量输出控制,几个菜单界面等。-This is a development of our own products- electronic expansion valve drive equipment, using ARM7 as single-chip,it contains a stepper motor drive module, analog acquisition processing
MC68375Source
- 程序是在MOTO单片机68375上开发的,主要实现了信号量采集、模拟量采集、开出控制等功能。-Procedure is in the MOTO 68375 single-chip development,the main achievement of the signal acquisition,analog acquisition,out of control and other functions.
ADC0804PLCD1602
- STC单片机+ADC0804+LCD1602实现模拟量采集液晶显示输出-The STC the microcontroller+ADC0804+LCD1602 achieve analog acquisition LCD output
ADC
- PIC16F87用数码管显示的单通道模拟量采集器-The PIC16F87 with digital display of single-channel analog acquisition
TEST
- 4通道4-20mA模拟量采集板通过RS485总线发送采集数据给PC机(The 4 channel 4-20mA analog acquisition board transmits data to the PC through the RS485 bus)