搜索资源列表
UCOS2在51上的移植源码V1.1
- UCOS2在51上的移植源码V1.1。学习UCOS的代码-UCOS2 51 on the transplant source V1.1. UCOS learning code
UCOS2在51上的移植源码
- UCOS2在51上的移植源码。学习UCOS-UCOS2 51 on the transplant source. Learning UCOS
PDIUSBD12固件源码
- 修改后的PDIUSBD12完整固件源码,实现51单片机的USB接口,完全通过测试。-revised PDIUSBD12 integrity of the firmware source code, achieving 51 SCM's USB port and fully tested.
曼码调制的非接触ID卡通用读卡程序编制
- 转载 曼码调制的非接触ID卡通用读卡程序编制 C语言代码程序如下: . /*H4001只读卡读码程序*/-reproduced Man Code Modulation non-contact reader ID cartoon programming with C language code is as follows :. / * Decoding CD-card reading * /
51单片机BCD码转换实验
- 51单片机BCD码转换实验
8051单片机实例之30个程序源码附原理图
- 此开发包内有30个实例程序源码,KEIL51编译,外加原理图.
多字节BCD码转换成十六进制
- 多字节十进制整数(压缩BCD码)转换为二进制整数子程序;入口:R0指向多字节十进制整数高位,R1指向结果多字节二进制整数高位,R7=n ;使用A,R0~R7,影响CY
B码发生器源代码
- 该程序是基于C8051F930单片机编写的B 码发生程序有一定的使用价值,请大家参考
12-ST库3.5.0源码
- stm32库相当全的源码,用来创建工程模板。(The STM32 library is quite full of source code used to create engineering templates.)
AOK虚拟示波器上位机源码及APP最新版
- AOK虚拟示波器的上位机源码,从串口获取下位机数据,然后绘制波形(AOK virtual oscilloscope host computer source, from the serial access to the next machine data, and then draw the waveform)
12864简易显示源码
- 12864简易显示源码,简单汉字显示,仅供参考(12864 simple display source code, simple Chinese characters display, for reference only)
3.码盘计数
- 基于stc15f2k60s2的码盘测速程序。可以测量码盘的速度。(Code speed measurement program based on stc15f2k60s2. The speed of the encoder can be measured.)
汽车诊断软件源码
- 汽车诊断软件的C语言源码 可以拿来学习学习(Automotive diagnostic software C language source code, you can learn)
div码表
- 可以通过keil形成hex文件,烧录到单片机上。通过按键的控制形成码表的计数,储存,复读,清零。(The hex files can be formed by keil, which can be burned to a single chip. The control of the keypad forms the number of the code table, storing, rereading, and clearing.)
程序员必备所有制码转换
- 二进制 ASCII码 八进制 十六进制 特点数位 逢10进1 逢2进1 逢16进1 美国信息交换标准代码(计算机键盘代码) 共256个字符每个字符8big BCD码(8421) 格雷码等(Binary ASCII code Octal number system Hexadecimal Characteristic digit 10 to 1 2 to 1 16 to 1 Standard code for the exchange of informati
STM32版FX2N源码&原理图(可直接移植)
- FX2N源码V3.8版的使用基本说明: 编译语言:C语言 FX2N源码V3.8版是根据三菱FX2N的PLC通信协议、通信命令以及基于STM32F103系列单片机上编写运行的程序,可以直接利用三菱编程软件编写梯形图下载运行,无需任何转换。 注:1)目前在STM32F103RD/STM32F103VC/STM32F103VD/STM32F103VE/STM32F103ZE测试通过; 2)本程序不完全支持所有梯形图指令,如果需要其他的功能,需要亲自己修改代码, 编译环境:
匿名飞控源码V1.4
- 匿名四轴飞控主板源码V1.4,无人机,领航者(ANO V1.4 master Source code (Four axis aircraft, UAV))
匿名信号板源码V1.4
- 匿名信号板源码,包含ANO_Link_PC和ANO_Link_Plane两者源码(ANO Signal board source code UAV Four axis aircraft)
OBD故障码解析
- OBD系统开发时OBD故障码解析,含大部分整车生产企业自定义的代码以及通用代码(OBD fault code parsing during the development of OBD system, including custom codes and general codes of most vehicle manufacturers)
100多个单片机源码
- 100多个精心挑选打包得的单片机源码,毕业设计比用,可以参考的源代码