搜索资源列表
2MSP430F149USART1sendreceivewithpc
- 使用MSP430F149芯片,透过串口与电脑发送接收通信,波特率9600,8数据,无校验。使用32.768k晶振,使用P3.6和P3.7口作为发送和接收口,使用异步通信USART1,采用中断形式。实现通信,当单片机接收到什么字符后,它会自动把接收的字符发送个电脑-MSP430F149 chip computer through the serial port and send and receive communication baud rate 9600 data, no parity. 32
BAUD
- DSPIC6014 波特率自动检测,使用回归计算的源代码-DSPIC6014 auto baud rate detection, use the source code of the regression calculation
BAUD1
- DSPIC6014 波特率自动检测,使用简便计算方法的源代码-DSPIC6014 auto baud rate detection, easy-to-use calculation methods source code
baudrate-calculate
- 波特率计算程序,可以不用对比波特率表格自动计算数值。-baudrate calculate of intercommunity
51serial-communication
- 51单片机串口通信配置模板 定时器方式2: 8位自动重装 波特率 96-51 single-chip serial communication configuration template Timer Mode 2: 8-bit auto reload Baud 9600
MG323_MSP430F449
- 用MSP430F449把华为MG323波特率自动改为48-MSP430F449 used to automatically change the baud rate 4800 Huawei MG323
STC12AUTO-BAND
- 采用STC12C5A60S2单片机 双串口 可自动识别485信号的波特率 固定采用PELCO-D的云台通讯协议 一个串口接收PELCO-D的辅助命令 另一个串口将收到命令转换发出-Two serial microcontroller using STC12C5A60S2 can automatically identify 485 baud rate is fixed using PELCO-D PTZ protocol PELCO-D receives a serial auxiliary p
MSP430-display-uart
- 在串口调试助手中的发送区选中:“十六进制发送”和“自动发送”,以十六进制形式,以字节为单 位输入某个数字,如03,这样单片机会接受到,送到数码管显示该数字。若连续输入“030205”,单 片机其实是接受到了来自PC的以9600波特率,8个数据位,一个停止位的无校验位的字符串,显示器 瞬间显示了3、2、5,看到的是最后的数字5-msp430 receive and display it
chaxunjieshou
- 串行口工作在方式1时,数据为8位,从RXD端输入,从TXD端输出,其波特率固定。在CPU将数据写入发送SBUF寄存器后立即启动发送,待8位数据输完后,硬件自动将TI置为1,TI必须用软件清零。8位数据接收完时,接收SBUF寄存器满,则硬件自动将RI置为1,RI必须用软件清零。-8-bit data transmission is complete, the hardware will automatically TI is set to 1, TI must be cleared by soft
UART1_UART2_TRANS
- STC单片机双串口,串口1,2测试程序,串口2使用定时器2作为波特率发生器。实现自动转发功能。来源STC官网。-STC SCM dual serial port, serial port 2 1,2 test program, using timer 2 as a baud rate generator. Automatic forwarding function. Source STC official website.