搜索资源列表
l298
- l298调 速 程 序 常规的接法是这样的，EnableA接PWM信号，Input1输入正反控制信号， Input2是Input1经过反相以后的信号。L298的电平是与TTL电路相兼容的，一般是超过2.5V就为高电平。假如Input1为高电平时电机正转，那么低电平时就是反转，PWM信号控制电机的转速。 _________________
bujindianji
- 基于L298的单片机PWM控制步进电机的转向和速度
tracking
- 基于ARM7循迹小车 光线自适应控制 l298 pwm控制-tracking car,ARM7-based， adaptive light control ， driver chip L298 ,speed control with PWM
pwm
- 利用延时产生pwm信号，通过L298功率放大器驱动直流电机- pwm DC-motor
PWMCtrl
- 基于TI公司的MSP430单片机的PWM调速程序-Based on TI' s MSP430 MCU PWM speed control process
L298andxiaoche
- 用keil 52写的L298的驱动程序。其中pwm波由软件仿真产生，用定时器实现，能够同时产生两种不同的PWM波从而实现两个电机的不同转速。经过测试通过。-Keil 52 written by the L298 driver. Pwm wave which generated by the software simulation, using timers to achieve, can produce two different kinds of PWM wave in order to ac
PWM
- 写的程序为pwm驱动直流电机 用的是L298驱动 并用四个按键 实现电机的速度变化 -Writing programs for dc motor using PWM driven by four buttons is L298 drive motor speed variation. Realizing
PWM
- 基于单片机控制的PWM直流调速系统 测速 L298-Microcomputer Control of PWM DC Speed Control System L298
PWM
- 本直流电机PWM调速器主控芯片采用AT89C51，显示部件采用LED数码管，人机交互接口采用独立式键盘，电机驱动电路采用L298。该直流电机PWM调速器能实现电机正转，反转，停止，并能实时显示转动的圈数。-PWM DC motor speed controller of the master chip AT89C51, with LED digital display unit, interactive interface with separate keyboard, the motor dr
PWM
- PWM控制直流电机速度,通过4×4矩阵键盘调速，L298驱动电机-PWM control of DC motor speed by 4 × 4 matrix keyboard speed, L298 drive motor
PWM
- 本直流电机PWM调速器主控芯片采用AT89C51，显示部件采用LED数码管，人机交互接口采用独立式键盘，电机驱动电路采用L298。该直流电机PWM调速器能实现电机正转，反转，停止，并能实时显示转动的圈数。-The DC motor PWM speed controller master chip AT89C51, the use of LED digital tube display unit, interactive interface, the use of stand-alone keyb
pwm
- 52单片机电机pwm调速功能，c程序可以用l298等芯片控制调速-52 single-chip motor pwm speed control function, c chip program can control the speed with l298, etc.
l298
- L298驱动程序，PWM控制，带正反转控制，挺好的库-L298 driver, PWM control, with Reversible control, very good library
zhi-liu-dian-ji-L298-PWM
- stc12c5a60s2产生PWM经过L298控制5V直流电机-stc12c5a60s2 generate PWM control 5V DC motor through L298
DC-PWM-speed-control-system
- 直流脉宽调速系统：使用STC单片机模拟PWM控制L298来驱动电机，首先设定电机速度(转/分钟)。电机自动恒定转速在设定值。也可以实时调节转速。没有算法。-DC PWM speed control system: Using analog PWM control L298 STC microcontroller to drive the motor, first set the motor speed (rev/min). Constant speed motor automatically a
L298
- L298驱动，可以用来驱动电机，用到pwm，可以直接用-L298 drivers can be used to drive the motor, use pwm, can be used directly
motor-control
- L298通过pwm波驱动直流电机，电机为12v或者5v，是用51单片机开发的。-L298 pwm wave driven by a DC motor, the motor for 12v or 5v, with 51 MCU development.
pwm
- atmgega128PWM例程，用应于L298驱动的电机-atmgega128PWM routines should be used to drive a motor L298
dianjizhuansu
- 用51单片机输出pwm的占空比控制电机转速(The output speed of PWM is controlled by 51 single-chip microcomputer, which is controlled by duty cycle)
PWM电机 - 副本
- 驱动直流电机，通过l298n来驱动，stm32板拉高引脚PA9与PA10，同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)