搜索资源列表
CS8900A_汇编实现51单片机的TCP_IP协议
- 在51单片机上用汇编实现的TCP/TP协议网络通信，1、可以接收和发送帧 2、 实现了ARP报文传输；3、 ARP应答；4、实现了ICMP协议 5、 可以被其他网络中的主机Ping到 6、 实现了UDP协议-in 51 MCU used to achieve a compilation of TCP / TP network communication agreement, one that can receive and send two frames to achieve the ARP p
TCPmodbushy
- tcp/modbus应用程序,实现了UDP,TCP,把串口通信转换成网络通信-tcp / modbus connection application procedures, the UDP, TCP, put into serial communication network communication
Ethernet44B0
- ARM UDP通信软件，硬件环境为44B0+8019.该软件可以实现44B0和PC之间的UDP通信传输文件。-ARM UDP communications software, hardware environment for the 44 B0 8019. The software can be achieved 44B0 and PC UDP communication between the transmission of documents .
Example
- ZLG DP-668 开发板全部程序 \\BELL\\ 蜂鸣器演示程序 \\CAN测试程序\\ CAN双机通信演示程序 \\EEPROM\\ 24WC02演示程序 \\LCD\\ 128*64液晶模块演示程序 \\RED\\ 红外收发器演示程序 \\RS232\\ RS232串行接口演示程序 \\RTC\\ PCF8563时钟芯片演示程序 \\TCPIP\\ TCPIP通信演示程序（包含PING功能,及TCP,UDP等协议） \\串口通讯\\ 单片机与PC的R
UDP-communication
- 这个文件当中介绍了单片机UDP通信程序的编写，能实现与上位机的数据交换-This document which describes the preparation of SCM UDP communication program that can realize the data exchange between PC and
SerialDemo
- 是无线医疗软终端的代码，采用Udp通信，也展示了如何用232串口编程、Usb编程等与无线医疗传感器硬件通信的技术。-Medical software for wireless terminal code, using Udp communication, but also shows how to use the 232 program, Usb programming and wireless medical sensor hardware communications technology.
application
- arm板和上位机UDP通信代码，协议自定义-UDP socket
51MCU-UDP
- 51单片机与pc建立的UDP通信，对写UDP通信的有点帮助-51 pc set up the MCU and UDP traffic, UDP traffic for a little help to write
The-Comunication-of-LM3SPlwip-UDP
- 实现LM3S8962与上位机的UDP通信，内含VC界面，可调试。-LM3S8962 UDP communication with the host computer, containing VC interface debug.
IIU_bak
- 51单片机+ENC28J60实现局域网的UDP通信，上传温度信息。-51 microcontroller+ ENC28J60 LAN UDP communication, upload the temperature information
udp_echo_server
- stm32 lwip udp实现回显服务器，进行UDP通信-stm32 lwip udp achieve echo server for UDP traffic
UDP
- stm32与w5500模块通信的UDP例程，亲测可用-UDP routines stm32 module to communicate with the w5500, pro-test available
enet_uip
- enet_uip TI Cortex-M4 LWIP+UDP 通信源码。 可正常通信。-enet_uip TI Cortex-M4 LWIP+UDP
SIM900A-UDP-silent
- SIM900A UDP例程。使用UDP通信来控制开发板上的LED。-Use sim900a creat udp connect.use udp chain control LED which are on the STM32 board.
UDP0613
- 基于STM32F427的一个程序，包含双CAN通信，MCP2515，RMII 接口UDP通信，可以直接寄存器方式访问FPGA内部数据(STM32F427 based program, including double CAN communication, MCP2515, RMII interface, UDP communication, you can directly register access to FPGA internal data)
UDP传输数据-RTC触发STOP
- NB-IOT stm32开发板的参考资料 UDP传输数据-RTC触发STOP(NB-IOT STM32 development board reference UDP transmission data -RTC triggers STOP)
UDP传输与接收数据
- NB-IOT stm32开发板的参考资料 UDP传输与接收数据(NB-IOT STM32 development board reference data UDP transmission and receiving data)
UDP上下收发数据控制LED-定向IP
- UDP上下收发数据控制LED-定向IP NB-IOT-stm32l系列开发板(UDP up and down receiving and receiving data control LED- oriented IP NB-IOT-stm32l series development board)
网络通信实验
- 硬件资源: 1,DS0(连接在PF9),DS1(连接在PF10) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3/7寸TFTLCD模块(通过FSMC驱动,FSMC_NE4接LCD片选/A6接RS) 4,按键KEY0(PE4)/KEY1(PE3)/KEY2(PE2)/KEY_UP(PA0,也称之为WK_UP) 5,LAN8720(通过RMII接口驱动) 实验现象:
STM32L1xx低功耗单片机UDP透传源码
- STm32L系列单片机实现UDP通信的透传，开发环境为Keil，通信模块使用的是BC26。完整项目。