搜索资源列表
CAN模块程序清单
- 基于sja1000的CAN驱动程序 可以直接使用在现场总线中-sja1000 based on the CAN driver can be used directly in Fieldbus
SJA1000自测程序
- CAN总线控制器SJA1000的自测程序，硬件是利用SJA1000tx1管脚发出接收中断-SJA1000 CAN controller of the self-rated procedures, the hardware is used to give an acceptance SJA1000tx1 pin interruption
can
- 一个用sja1000控制器的can源程序-sja1000 using a controller can source
can——SJA1000
- SJA1000的驱动函数,can功能函数。-SJA1000 drive function, can function function.
can.rar
- can总线通信程序，运用SJA1000做CAN总线控制器，PCA82C250做CAN总线驱动器。曾经成功过，,can bus communication procedures, the use of CAN bus controller SJA1000 do, PCA82C250 do CAN bus drivers. Have been successful,
sja1000.rar
- sja1000can驱动程序，采用中断方式接收CAN 总线数据,sja1000can driver, using CAN bus data received interrupt
sja1000.rar
- CAN总线控制器SJA1000的设置和初始化代码，及收发函数。,CAN bus controller SJA1000 setup and initialization code, and sending and receiving function.
can-232
- 51单片机实现CAN总线和RS232协议之间的转换，内含SJA1000驱动程序，keil下编译通过。-51 MCU CAN bus and RS232 protocol conversion between, containing SJA1000 driver, keil compile.
sja1000
- CAN节点的测试程序, 实现两个节点传送数据，程序主要分三部分 SJA1000 的初始化,接收数据,发送数据. 学习Sja1000很好的参考程序实例-CAN node test procedures, the achievement of the two nodes to transmit data, procedures to initialize the main three parts of the SJA1000, receive data, send data. Sja1000 s
SJA1000
- SJA1000独立CAN控制器用户手册，用于CAN总线的开发设计参考-CAN controller SJA1000 independent user manual for the CAN Bus development and design reference
SJA1000
- sja的使用可以参考一下。。。。有一定的参考价值-SJA1000 reset initialization mode only for that. Including working methods to initialize the settings, the way to receive filter settings, receive Mask Register (AMR) and receive code register (ACR) settings, baud rate and in
SJA1000
- CAN总线用硬件，文档性文件，可供所有使用人员参考下载-document
sja1000.CAN.control(chinese)
- sja1000独立CAN控制器中文资料 -SJA1000 is a stand-alone controller for mobile targets and general industrial environment CAN Control Area Network which is the semiconductor PCA82C200 CAN controller PHILIPS alternative BasicCAN and it adds a new mode of PeliC
CAN
- CAN总线 SJA1000,适合初学者看，蛮容易的。-CAN bus SJA1000, suitable for beginners, the very easy.
can-node-communication
- 该程序已经被多次使用，需要两个sja1000 + 51 + pca82c250的通讯模块（本程序是在P2.6和P2.5设置了LED灯来显示是否通讯成功），将源程序（kaobei.hex）下载到51单片机中，上电后通过按下两个模块的复位键，就能看到对应的模块有指示灯显示-The program has been used many times require two sja1000+ 51+ pca82c250 communication module (the program is set in
sja1000
- sja1000直接加载到文件内 文件包能直接使用不用编写程序-sja1000 directly loaded into the document packages can be used directly without programming
SJA1000
- SJA1000驱动程序。它是CAN BUS通讯的控制器集成电路。可与DSP,FPGA连接-SJA1000 driver. It is the CAN BUS communication controller IC. With DSP, FPGA connections
can-can
- SJA1000通信源码，方便can通讯设计。-SJA1000 communication source, can facilitate the communication design.
CAN通讯实验-ST7793
- 基于STM32的CAN通讯网络的节点设置源程序(SJA1000 with STM32 to control the source process, C language.)
SJA1000英文版
- SJA 1000 CAN控制器芯片应用手册(Determination of Bit Timing Parameters for theCAN Controller SJA 1000)