搜索资源列表
attiny13---cd4052
- 使用attiny13定时器进行10小时长时间定时，程序原用于摄像机遥控器特定按键定时通断控制，attiny13控制模拟开关CD4052，源程序有详细说明，附电路原理图截图。调试通过。-10-hour timer with attiny13 long time, the program of the original remote control for camera buttons specific time-off control, attiny13 control analog switch
DJjiansu
- 用MSp430控制直流电机减速，用到了TimberA中的捕获比较寄存器。-DC motor control with MSp430 slow, use the TimberA the capture compare register.
PCA
- PCA捕捉模块0的CEX0被设置在按键S3对应的引脚上，按下和松开S3，将会产生下降和上升沿信号，引发捕捉模块动作。-PCA Capture Module 0 CEX0 S3 is set the corresponding pin in the key, press and release the S3, will result in decline and the rising edge signal capture module trigger action.
Sources
- 飞思卡尔争强捕捉模块 的三种测速 算法应用于智能车比赛 这是一个全局的构架 非常实用 好用-Freescale gaining the upper hand capture module of the three gun match algorithm is applied to the smart car is a very practical easy to use global framework
Freescale-program
- 飞思卡尔争强捕捉模块 的三种测速 算法应用于智能车比赛 这是一个全局的构架 非常实用 好用-Freescale gaining the upper hand capture module of the three gun match algorithm is applied to the smart car is a very practical easy to use global framework
hongwaicaiji
- 该程序是基于PIC单片机实现红外采集的原程序-The program is based on the PIC MCU infrared capture the original program
F340_key
- 本程序为PCA捕捉例程，判断4个(S1-S4)按键是否按下然后触发中断对LED灯 D2\D3取反同时也完成按键扫描的过程-The procedures for PCA capture routine, to determine four (S1-S4) button is pressed and then trigger the interruption of LED lights D2 \ D3 negated also completed the process of key scan
STC320AIC23
- 单片机中对STC320AIC语音AD进行寄存器设定，从而采集语音，然后发给DSP进行处理-Voice MCU AD to register on the STC320AIC set to capture voice, and then sent for processing DSP
Mc9s12xs128_video_program
- 飞思卡尔单片机 MC9S12XS128 单片机 摄像头采集程序-Freescale MCU MC9S12XS128 camera capture program
ARM
- 以S3C2410处理器为核心，控制摄像头采集图像，可以应用于监控。-S3C2410 processor core to control the cameras capture images, can be applied to monitoring.
ECT
- This a program for the ECT of freescale s MC9S12XDP512.16-bit main counter with 7-bit prescaler 8 programmable input capture or output compare channels Four 8-bit or two 16-bit pulse accumulators-This is a program for the ECT of freescale s MC9S12XDP
demo_11_3
- 基于T/C1捕捉功能的可变量程频率计的设计与实现 AVR ATmega16单片机设计-Variable based on T/C1 capture range frequency meter Design and Implementation of AVR ATmega16 microcontroller design
Output-Compare
- Freescale 增强型输入捕捉 输出比较-Freescale Enhanced Input Capture Output Compare
ECT
- freescale 程序编程 加强型捕捉定时器模块-freescale programming enhanced capture timer module
inputcapture
- :以输入捕捉中断方式,开关拨动使捕捉中断取反指示灯PTA1，使其闪动-: The input capture interrupt, the interrupt switch toggle to capture the inverted light PTA1, it flashes
vb_src
- AD認證，使用ADSI介面，並且可抓取AD的user object-AD authentication, use the ADSI interface, and can capture the user object AD
CAPCOM
- 英飞凌XC167单片机的捕获比较单元驱动！搞c166核心的可以-Infineon XC167 microcontroller capture compare unit driver! C166 can look out the core
STM8_TIM1_PWM_INPUT_CAPTURE
- STM8 的TIM1输入捕获程序模块参考!-STM8 the TIM1 input capture program modules reference!
The-final
- 利用定时器A每隔62.5ms 采集一个电压值 采集20个值后 取平均值 然后送到数码管显示出电压值-Timer A capture every 62.5ms using a voltage value of the acquisition value averaging 20 and then sent to the digital display the voltage
OrCAD15-7DemoTutorial
- Good tutorial in Orcad Capture and Orcad PCB designer including creation of full adder step by step.