搜索资源列表
OILsource
- 汽车电子OIL配置代码，用户可以直接用此工具配置用户任务的行为-Automotive Electronics OIL configuration code, the user can direct the user to use this tool to configure the behavior of the task
ADC
- 单片机程序源代码 AD转换 串口通讯 定时器配置 端口配置 延时 I2C通讯 UART串口，KEIL开发环境 -Microcontroller program source code to configure the AD converter serial communication port configuration latency timer I2C communications UART serial port, KEIL Development Environment
uart
- Also the USART automatically senses the start of transmission of RX line and then inputs the whole byte and when it has the byte it informs you(CPU) to read that data from one of its registers. The USART of AVR is very versatile and can be setup
USB2401
- 该驱动是以AT89C2051 单片机进行制作的，您只需修改 NRF2401.H和NRF2401.C文件中的部分代码，即可快速的实现不同微 处理器的移植工作，并且在NRF2401.H文件中已经做了详细的介绍-All configuration registers configure the driver 2401 is made AT89C2051 microcontroller, you need to modify the NRF2401.H and NRF2401.C file pa
spi
- 此为Silicon Lab单片机F340开发的源代码，单片机通过SPI接口配置时钟芯片。-This is Silicon Lab SCM F340, with source code, the microcontroller through the SPI interface to configure the clock chip.
RANDOM-CHARACTERS
- This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil for the 8051 chip. download here: https:/
LCD-MESSAGE
- This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil for the 8051 chip. download here: https:/
clock
- This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil for the 8051 chip. download here: https:/
Buzzer-2
- This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil for the 8051 chip. download here: https:/
reg89c5131
- This a header file for 8051 Keil uVision 3 This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil fo
keypad_driver_stm32-2.0
- 基于STM32的中断4*4矩阵键盘驱动，代码规范，结构清晰，易于配置。-Based on the STM32 interrupt 4* 4 matrix keyboard driver, code specification, clear structure, easy to configure.
User
- 关于stm32的开发，只有原码~~环境自己配置-About stm32 development, only the original code ~ ~ environment to configure their own
RFDK_RFM95_V2.1
- rfm95的测试DEMO源代码，包容如何使用此RF模块，如何配置-rfm95 test DEMO source code, inclusive how to use this RF module, how to configure
AN003
- 本应用笔记的目的是介绍如何配置和使用片内温度传感器。本文提供了配置说明和示例代码。 温度传感器产生一个与器件基材温度成正比的电压，该电压作为一个单端输入提供给ADC（模数转换器）的多路开关。当选择温度传感器作为ADC的一个输入并且ADC启动一次转换后，可以经过简单数学运算将ADC的输出结果转换成用度数表示的温度。-The purpose of this application note is to describe how to configure and use the on-chip t
C167-uart
- C167单片机串口初始化dave配置及测试输出代码-C167 microcontroller serial port initialization to configure and test the output code dave
stm32-interrupt
- stm32的中断程序的编写属于教学用的源代码 能够教你正常的配置外部中断 的各个函数-write stm32 interrupt routine belonging teaching source code can teach you properly configure each function of the external interrupts
RM04
- 应用单片机配置无线模块RM04、实现无线通讯的代码-The application of SCM to configure the wireless module RM04, the realization of wireless communication code
oscillograph
- 本示波器代码是以stm32f407为硬件基础，通过对12位adc，dma，以及定时触发模式的配置，最终在12864液晶屏上显示波形。-This oscilloscope Code is stm32f407 based hardware, by 12 adc, dma, and configure the timing trigger mode, the final display waveforms on 12864 LCD screen.
kalman
- 卡尔曼滤波程序的单片机代码实现方案，需要自己配置参数进行效果调试。-Kalman filtering program microcontroller code program, you need to configure the effect parameters themselves debugging.
STM32F405RGT6-DA-4922
- STM32F405RGT6 采用STM32CubeMX自动生成配置代码，配置SPI驱动MCP49-STM32F405RGT6 use STM32CubeMX automatically generate configuration code, configure the drive MCP4922 SPI