搜索资源列表
MjKzyC2p02
- 磨机控制仪测试程序采用STM32+12864(0108)+PCF8563+PID控制可以通过对磨音采集来控制球磨机工作在最佳负荷-Mill control device test program using STM32+ 12864 (0108)+ PCF8563+ PID control can be achieved by controlling the ball mill grinding sound acquisition work in the best load
WEIGHT
- 基于MSP430F5438的称重传感器的设计,称重值能够通过12864液晶进行显示,并且有4-20MA电流输出,非常实用。-Design MSP430F5438 load cell based weighing value can be through 12864 LCD display, and there 4-20MA current output, very practical.
modbus
- 基于MSP430F5438的单片机通讯程序设计,使用MODBUS通信协议,并伴有压阻式称重传感器的重量测量。-MSP430F5438 MCU-based communications program design, using MODBUS communication protocol, and load weight measurement with piezoresistive sensors.
BLDC-6-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的stm32单片机开发的电位器调速的BLDC控制程序-Compiled by keil4 stm32 MCU development of potentiometer speed of BLDC control program
BLDC-3-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的电位器3路调速pwm控制的BLDC控制电路-Keil4 compiled with potentiometer 3-way control BLDC pwm speed control circuit
test
- 基于STM32的二轮平衡车,经测试能够直立平稳,在该参数可以前后懂负载并爬坡-Based on the STM32 two balanced car, tested can stand steady, at around the parameter can understand the load and climbing
nokia5110
- nokia5110库 蓝牙这是一个家居系统程序内容详细简单上手快-Nokia5110 library Bluetooth- this is a detailed simple household system program content on the load
Smart-socket
- 基于51单片机实现的智能插座,可实现定时,恶性负载识别,自动断电等功能,包含proteus仿真图-Based on 51 MCU intelligent socket, it can achieve timing, bad load recognition, automatic power-off function, including proteus simulation map
LEDdianyuan
- 输入交变电源的电压220V,50Hz;直流电压的输出小于10V。 ① 电流输入的大小范围:200mA到2000mA之间; ② 可以在允许的范围内通过矩阵键盘设定电流的预设值,显示模块会显示预设的电流值,设计要求预设电流与实际输出电流值相差的绝对值要小于或者等于输入的电流值的1%。 ③ 为了增强可调节性,该设计还具有加减的步进功能,步进为10mA; ④ 负载的电阻改变,电压输出值同样不会高于10V,精度方面输出电流的误差绝对值要小于等于预设电流值的1%。 -The design
kaiguandianyuan
- (1)输出电压可调范围:2~22 V,步进0.2 V; (3)输出噪声纹波电压峰-峰值,DC-DC的满载效率; (4)可以通过按键调节输出电压,并在LCD上显示开关电源的参数相关信息; (5)具有故障自诊断,过压、过流保护等功能。-(1) Output voltage adjustable range: 2 ~ 22 V, stepping 0.2 V (3) output noise ripple voltage peak- peak, DC-DC full load eff
TM7710_C51
- 使用双路24BIT模数转换TM7710做的电子秤电路,程序只使用了其中一路,称重传感器是500g的。-Use dual 24BIT ADC circuit TM7710 do electronic scales, the program uses only the way in which the load cell is 500g of.
dianzhifuzai
- 电子负载 有恒流和恒压2种方式 OLED显示-Constant current and constant voltage electronic load 2 ways OLED display
DAzhuanhuanqi
- 基于AT80c51的D/A转换器,文件包含hex,c文件,和仿真文件,可将hex文件载入仿真文件即可运行-Based AT80c51 a D/A converter, the file contains a hex, c files, and simulation files, you can load a hex file to run simulation files
LCDyejingxianshi
- LCD液晶显示文件包括仿真文件,hex文件,C文件,PWI文件,可将hex文件载入仿真软件,即可实现仿真-LCD display files including simulation files, hex files, C files, PWI file, you can load a hex file simulation software, simulation can be realized
IFDOMEO_ca3189e
- C51,RF通信专用的中频解调IC,很难找到,对通信机设计有很大帮助.快快下载.-C51,RF IF IC,VERY GOOD,LOAD OK!
PCB
- 安装有四个负载单元,采用多通道、24位模/数转换器(ADC)检测平板上的物体重量和重心。称重器提供最高780g的满幅响应。用户界面实时显示平板的重心和实测总重量。除了作为智能压力传感器外,设计也非常适合具有压力检测功能的触摸屏接口。-The weight and the center of gravity of the flat plate are detected by using a multi-channel, 24 bit analog/digital converter (ADC),
windmotor
- 本设计介绍的是直流无刷电机的正弦波控制方式,以及基于英飞凌 XC866单片机的三相带霍尔传感器直流无刷风机 180 度控制方案。三相带霍尔传感器直流无刷风机 180 度控制系统主要由以下几大部分构成:整流电路、逆变电路、控制电路、驱动电路、开关电源、直流无刷风机及扇叶负载。-Is the design of the brushless DC brush motor sine wave control mode, and based on three-phase Infineon xc866 mi
solarmodal
- pv panel for converter along with mppt for all types of load
Load-Cells
- 本程序基于stm32和ad7706的多路压力采集系统,具有速度快,精度高的优点。-The program is based on multi-channel pressure ad7706 stm32 and acquisition system, high speed, high accuracy.
MjKzyC2p02
- 磨机控制仪测试程序采用STM32+12864(0108)+PCF8563+PID控制可以通过对磨音采集来控制球磨机工作在最佳负荷-Mill control device test program using STM32+ 12864 (0108)+ PCF8563+ PID control can be achieved by controlling the ball mill grinding sound acquisition work in the best load