搜索资源列表
短信收发系统 OF MSP430
- 由MSP430 控制实现的 短消息收发功能的系统 可利用单片机的 串口与无线MODEM 进行连接在进行发送和解析数据 必须按照PDU的格式进行处理-MSP430 control achieved by the Short Message System transceiver functions of the MCU can be used with wireless modem serial port to connect to send and conducting analytical da
Waveform1
- MSP430串口发送程序，源码-MSP430 serial procedures, source
UART_Send
- 基于msp430的软件模拟串口发送程序（在MSP430F147型单片机上成功实现）-Controller Based on the simulation software Serial this procedure (MSP430F147 MCU - successful realization)
1t
- MSP430串口发送程序，使用C语言编写，1发-Send MSP430 serial procedures, using the C language, 1 fat
uart
- 串口通讯实现发送的程序 MSP430单片机C语言 AIR-Serial Communication MSP430 realization procedures sent Singlechip C language AIR
msp430f149monichuanku
- 这是在TI网站上下的例程，绝对可用， P2.2,p2.3，在示波器上调试，调BitTime可以调节脉冲宽度，就可以调节波特率了，模拟串口发送一个字节需要发10位，起始位＋8位有效数据＋停止位，二真实串口不用发起始和停止位，因为缓冲区已经将他们加上了-This is a site from top to bottom in TI routines, absolutely available, P2.2, p2.3, in oscilloscope debug, tune BitTime can
msp430app
- 基于MSP430的油层界面监护系统。可以根据传感器检测到的乳化层数据，存储并显示在LCD上，并可通过串口发送到其他设备。-This monitor system is based on MSP430 chip. Store and display on LCD the data that the sensors sent.And it can send the data to other device via RS232
MSP430_Uart0
- MSP430串口程序，串口接收与发送均用中断处理。当MSP430串口中断接收到PC机的指令后通过中断发送将数据发送出去。-MSP430 serial program, serial port receive and send all use interrupt handling. When the MSP430 serial receive interrupt instruction PC, adopted after the break to send the data sent.
main
- MSP430 串口RS232程序向PC发送0~127ASCII码-MSP430 Serial RS232 to the PC program code to send 0 ~ 127ASCII
entire_pcb
- MSP430单片机实现12位ADC转换并将采集的数据通过串口协议发送。每个12位数据按照“l”，数据第八位，“h”，数据高八位的顺序用四次发送出去-MSP430 MCU and 12-bit ADC conversion data collected through the serial port protocol to send. Each 12-bit data in accordance with the " l" , data, eighth, " h"
MSP430Serial
- MSP430串口发送程序 -MSP430 serial port program
ME008-UART0
- msp430串口调试程序，通过串口助手发送一个字符给单片机,单片机将数据回发给串口助手-msp430 serial debugger, assistant to send a character through the serial port to the microcontroller, microcontroller serial data sent back to assistant
msp430adc12uart0
- 利用串口调试软件 向串口发送一个字符,MSP430单片机接收到后从低功耗中唤醒，执行AD采样.并将采样结果发送到电脑上的串口调试软件中.单片机发送完后又进入低功耗状态.-msp430f149 usart0 adc12
serial-port-test-program
- MSP430单片机串口测试程序。该程序将串口收到的字节发回主机，供测试串口用。用串口调试助手向430发送任意字符串，将接收到同样的字符串.也可用Windows自带的超级终端，设置波特率2400，8位数据，无校验无流量控制，连接。计算机键盘上按任意字母，屏幕会有回显。-This is a serial port test program on MSP430 MCU.
main
- MSP430串口通信 /***************************************************** 程序功能：MCU不停向PC机发送数据,在屏幕上显示0~127对应 的ASCII字符 ------------------------------------------------------ 通信格式：N.8.1, 24-MSP430 serial communication /********************************
GSM
- 这是一个MSP430单片机控制GSM模块的信息。 控制器通过串口发送AT指令集，控制GSM模块发送短息，拨打电话。-MSP430 MCU control the GSM module sending message or phone through AT command.
LowPower
- 18b20测温通过msp430串口发送给电脑。实时显示温度信息-18b20 temperature via msp430 serial port to send to the computer. Real-time display of temperature information
Compass-MSP430
- 基于MSP430的电子罗盘，控制步进电机带动指针指向正北，并将电子罗盘数据及单片机平台的航向通过蓝牙串口发送至PC端程序上显示。实现了MSP430包括HM3883l电子罗盘、步进电机、带软件FIFO的串口模块的驱动。-Electronic compass based on MSP430, control the stepping motor drives the pointer points to the north, and the electronic compass data and si
HC-06
- HC-06 蓝牙模块驱动程序， MSP430串口发送和接收-driver code for bluetooth module HC06
main
- 单周期循环PWM可调占空比输出（4种波形，可选择输出），ADC数据采集（8路），串口调试将采集到的数据发送到串口工具，GPIO状态指示灯。(Single cycle PWM adjustable duty cycle output (4 waveforms, optional output), ADC data acquisition (8 way), serial port debugging will collect data to serial port tool, GPIO status