搜索资源列表
SMS_Mcu_Program
- 做过的一个单片机项目的完整程序,包含对tc35i无线通信模块的控制,GB2312与Unicode之间的转换,液晶模块控制等。-done a complete SCM process of the project, including right tc35i wireless communications module control, GB2312 with Unicode conversion between the LCD module control.
ARMkaifayaodiao
- 基于arm的嵌入式程序开发要点分析 讲述嵌入式开发的全过程-based arm of embedded programming elements embedded analysis on the entire process
16+2LCD
- 此为8051单片机的LCD开发程序,经过了编译,仅供大家参考(1)-for 8051 LCD development process, after translating and only reference (1)
eeprep
- nrf24E1模块eeprom的读写程序,通过SPI接口-nrf24E1 reader module EEPROM process, through the SPI interface
Poweron_initial
- 开机后的启动流程at89x51初始化及相关编程-boot after the start at89x51 initialization process and related programming
500bintohex
- bin to hex本程序是将bin文件转换为hex文件以适合不同的下载需求-bin to hex the process is to bin hex conversion of paper documents to suit the needs of different download
programasm
- 是我在电子竞赛期间写的一些单片机汇编程序-in electronic writing contest during the compilation process MCU
MCUTool
- 单片机开发过程中用到的多功能工具,包括热敏电阻RT值--HEX数据转换;3种LED编码;色环电阻计算器;HEX/BIN 文件互相转换;eeprom数据到C/ASM源码转换;CRC校验生成;串口调试,带简单而实用的数据分析功能;串口/并口通讯监视等功能. 用C++ Builder开发,无须安装,直接运行,不对注册表进行操作。纯绿色软件。-microcontroller used in the process of developing the multi-purpose tools, includ
bit_to_tib
- 一种简单的字节位颠倒的程序,调试通过了的-a simple byte-reversed process, the adoption of the debugging
datacollection
- 这是采用KeilC51进行编写的单片机程序,实现一个用于8路模拟信号采集、传输控制和显示系统。-KeilC51 This is used for the preparation of the SCM process, for the realization of an eight-channel analog signal acquisition, transmission, control and display system.
ISP20060417
- 并口ISP测试软件 说明:本软件的编写过程中,本人参考了网站上并口控制LCD液晶的程序,使用了其中的并口操作! 本软件只是测试版,支持MEGA8、MEGA16、MEGA32、MEGA64、MEGA128。但本人只测试过MEGA16和MEGA128,由于其中的一些程序写的不是非常优化,因此在操作MEGA128时有点慢,望各位注意!欢迎各位测试其它的型号,有什么问题请发邮件:avrarm@126.com,非常感谢! 以后本人继续努力,争取增加一些其它型号单片机和其它的一
CAN_Zongxiantongxun_AVR
- MCU:ATMEGA8515 Frequence: 16M 描述:利用已有CAN TEST V1.0电路板进行调试, 可靠性测试已通过,并发现8515外部中断不稳定 的原因是没有在INT0脚加上拉电阻,加上后已能 够稳定地运行 调试过程中发现SJA1000的首地址设置有误,改过 后,当CAN发送数据时,程序能进入中断了,但发现 中断是由出错报警中断引起的,估计与波特率设置 有关。 通过修改CDR的参数,以及更换16M晶振,现在已能 正常地收发送数据了-
alskdjlaskhd
- msp430单片机基于modem数据传输的通讯程序设计-Controller SCM modem data transmission based on the design of the communication process
rtx51fangzhen
- keil c51 RTX-tiny 在Proteus 6.7的仿真程序。边看程序边仿真,爽啊。-Keil RTX-tiny Proteus 6.7 of the simulation program. While watching process simulation, Cool.
14.2.2PID_control(2)
- 本上载源码为用51汇编语言实现pid控制的发生的程序-uploaded the source code for the 51 assembly language used to achieve pid control of the process
51ToLCD
- 一个自己编写的,通过并口操作5.7英寸TFT液晶屏的汇编程序。主要流程是,设置液晶屏,然后从存储器里面读取显示数据,通过并口送出。-a prepared themselves through parallel operation 5.7-inch TFT LCD screen the compilation process. The main process is set up LCD screen, and then read from the memory inside shows data
ha0054t-1
- HT95xxxx来电显示应用,完整的来电显示程序,三种来电显示模式-HT95xxxx CND applications, CND integrity of the process, three CND model
sejishilu
- 本文从硬件和软件两方面介绍了MCS-51单片机温度控制系统的设计思路,对硬件原理图和程序框图作了简捷的描述。-paper from the hardware and software aspects of two MCS-51 temperature control system design, right hardware schematic diagram and the process was simple descr iption.
wb-cpu
- 该套软件用于提取王码98(或者其他版本)的五笔数据,精简后应用于嵌入式系统,如单片机。在DOS下,用TC模拟调试通过。很容易移植到单片机上。含五笔数据提取过程,输入时两分法查找的子程序。全部为C代码-the software used to extract Wangma 98 (or any other version), the five data streamlined used in embedded systems, such as SCM. In DOS, using simulati
DS18B20qudongchengxu
- 用c语言写的时钟芯片读的程序,可运行,检查通过的。SD2300C51读时钟程序 .C-language used to write the clock chip-reading process can be run through the inspection. SD2300C51 time clock procedures. C