搜索资源列表
AT89CXX
- 8051单片机刻录程序彻底公开 用于单片机刻录器-8051 recording process completely open for SCM burner
PCBwzlct
- FLASH制作的PCB电路板加工整个流程,难得珍贵-FLASH produced by the PCB processing the entire process, rare precious!
kongzhi
- 从其它网站看到的程序,框架不错,做单片机控制很有参考价值。后缀改为.c即可-from other sites to see the process, the framework is true, do MCU control of great reference value. Suffix changed. C can
LCD_DR
- //使用说明: //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出, //键值返回信号从keyscan低4位读入, //故使用时硬件电路需要与之相对, //或者把软件中相应地方修改即可-/ / use : / / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1
44scan
- //使用前请先定义keyscan为单片机的 //某个端口,如#define keyscan P1 //程序中扫描信号从keyscan高4位输出, //键值返回信号从keyscan低4位读入, //故使用时硬件电路需要与之相对, //或者把软件中相应地方修改即可-/ / use the former post keyscan definition of SCM / / a port, keyscan such as # define P1 / / scanning proces
ds1624cprogram
- 由于DS1624是I2C总线结构的串行数据传送,它只需要SDA和SCL两根线完成数据的传送过程。因此,我们在进行程序设计的时候,也得按着I2C协议来对DS1624芯片数据访问。有关I2C协议参看有关资料,这里不详述。对于AT89S51单片机本身没有I2C硬件资源,所以必须用软件来模拟I2C协议过程。 要从DS1624中读取温度值,首先启动DS1624的内部温度A/D开始转换,对应着有相应的命令用来启动开始温度转换,有关DS1624的指令集参考前面的叙述。一般情况下,DS1624经过一次温度
ccontrol
- c语言编制的控制步进电机正反转,并且测试电极的启动速度及控制步进电机加速过程fft并画图的小程序-the stepper motor control reversion, test electrode and the launch speed and stepper motor control fft and accelerate the process of drawing small programs
kchap9
- 在USB 固件程序设计中的主循环程序-USB firmware design of the main recycling process!
RC_filter
- 计算RC(阻容)滤波时间常数的程序,有两种单位制,适合matlab65环境运行。 -calculated RC (R) filter time constant of the process, there are two unit system, matlab65 environment suitable for running.
HWMP3DECODER
- 外挂硬盘式解码程序,Keil语言编写验证-external hard-decoding process, Keil language test
7290C-datebase
- 此软件包包含了模拟I2C C51程序软件包和ZLG7290的C51程序然后包。 软件包的接口界面: (1) bit ISendByte(uchar sla,uchar c) (无子地址)写单字节数据 (现行地址写) (2) bit IRcvByte(uchar sla,uchar *c) (无子地址)读单字节数据 (现行地址读) (3) bit ISendStr(uchar sla,uchar suba,uchar *s,uchar no)(有子地址)读N字节数据
dianjicesu1
- 单片机开发程序,用以直流电机测速,并把所得值在七段数码管上显示出来。-MCU development process for the DC machine guns, and the values obtained in paragraph 107 of digital tube displayed.
1288711111
- 是有关于12887的初始化的一些处理,可以工参考-is on the 12,887 of the initialization process, and the Public Reference
chuankoumoli
- 用单片机软件模拟串口程序,只占用一个T2资源,对初学者很有帮助-MCU serial process simulation software, only takes up a T2 resources useful for beginners
anglemachine
- 《角度测量器》 用光电编码器测量角度,每个脉冲为0.72度。 测量范围:0.0~360.0度 为保证不错过脉冲,用timer1计数,在电平跳变中断里判断转动方向,尽量加快处理过程。 数据换算和数码管扫描显示在主循环中实现。 译码器用10米长5芯屏蔽线与数显器的两片74HC595连接。 MCU为12F629,使用内部4兆RC振荡和内部复位功能。 -"angle measuring device" using photoelectric encoder
24wei10jinzhiPINLVJI
- 可编程逻辑设计的程序!24位十进制频率计!可使EDA实验年箱测量指定频率!-programmable logic design process! 24 metric Cymometer! EDA will experiment, measurement designated frequency bins!
InitialiHT1381
- 关于ht1380时钟的程序,关于ht1380时钟的程序关于ht1380时钟的程序-ht1380 clock on the process, ht1380 clock on the procedures on the clock procedures ht1380
单片机
- 实现交通灯功能的汇编程序.-achieve functional traffic lights compilation process.
二进制转化十六进制浮点数
- 我用VC写的十进制与十六进制数的转化程序,绝对独创,可用于需要浮点运算的单片机编程数值转化。-I write with VC metric hexadecimal number and the conversion process, absolutely original and the need for the floating-point operations into numerical microcontroller programming.
lineonyejing
- 是一个在液晶上画斜线的C51的程序,希望对大家有帮助!-is a picture of the LCD slash the C51 process, we want to help!