搜索资源列表
GetKey
- 用单片机C语言编的通过键盘扫描得到键值的键盘扫描C程序的源代码,可供单片机开发人员参考。-MCU series of the C language keyboard scan keys keyboard scan C program's source code available to developers SCM reference.
454353AVR_PROGRAM
- AVR单片机的C语言源程序,包括按键扫描\\EEPROM通讯\\LCD显示\\数码管显示等等的源程序DEMO代码-AVR C language source files, including keystroke scan \\ EEPROM communications \\ LCD Display \\ Digital Display, etc. of the source code DEMO
CH341PAR.ZIP
- 键盘扫描LED驱动芯片ch451资料及c语言源代码-keyboard scan LED driver chip ch451 information and c language source code
Voltage_C_Program
- 八路电压表C程序 使用AT89C52单片机,12MHZ晶振,P0口读入AD值,P2口作AD控制,用共阳LED数码管 P1口输出段码,P3口扫描,最高位指示通道(0-7)。-Eight-way voltage meter C program using AT89C52 single-chip, 12MHZ crystal, P0 I read into the AD value, P2 I make AD control, with a total of P1 Yang LED digit
445
- 数字音乐盒 (1) 硬件电路中用P1.0~P1.7控制按键,其中P1.0~P1.3扫描行,P1.4~P1.7扫描列。 (2) 用P0.0~P0.7,P2.0~P2.7控制LED,其中P0.0~P0.7控制七段码a,b,c,d,e,f,g,用P2.0~P2.7为数码管位选信号。 (3) 用,P2.0~P2.2作为LCD的RS,R/W,E的控制信号。用P0.0~P0.7作为LCD的D0~D7的控制信号。 (4) 用P3.7口控制蜂鸣器(J2,J4断开,J3短接)。 (5) 电路为
Key_Scan
- 运行后按着几个按键,将在屏幕上显示其扫描码,无键被按则显示Nokey! 经试验一般可检测8个按键同时被按下! 为C语言编写TXT格式源码,改后缀名后可运行。-Running according to a few keys will be displayed on the screen of its scan code, no keys are displayed according to Nokey! May generally be detected by the test butto
keyboard
- 嵌入式键盘,wince下可热插拔,at89s52 模拟ps2键盘,第二套扫描码-Embedded keyboard, wince under the hot-swappable, at89s52 simulation ps2 keyboard, the second scan code
temp
- 注意:只有C代码。串行驱动led显示,一个74hc595位移寄存器驱动三极管驱动led位,两个74hc595驱动led段,方式位5位x8段x2=10个数码管5分频,每次扫描时间位1.25ms-Note: Only C code. Serial driver led display, a shift register 74hc595 drive transistor drive led, and led two drives 74hc595 paragraph, ways x8 paragraph
keyboarddriver
- 4*4键盘扫描c语言驱动程序,包括源代码,硬件电路图-4* 4 keyboard scan driver c language, including source code, hardware schematics
key
- scan P0_key_1.c与\cpubbs_scankey_receiver_cn\以中文方式接收单片机发送回来的键值.vi配合使用,当你按了某一个键时,它会把你按的键码发回来,并以中文显示。C51机串口可以发中文.-scan P0_key_1.c with \ cpubbs_scankey_receiver_cn \ in order to receive single-chip Chinese to send back the keys. vi use, when you press a
code
- 51单片机的几种基本外设运用,例如:温度传感,时间芯片,按键扫描,LCD控制等C语言例程。-Several basic peripherals 51 MCU application, such as: temperature sensing, time chip, key scan, LCD control, C language routines.
PS2_Keyboard
- 51单片机的一个基于C语言的PS2键盘扫描识别程序,添加相应的扫描码库后即可下载到板子上使用-51 single-chip a PS2 keyboard scan identification procedures based on the C language, add the appropriate scan code library can be downloaded to the board
barcode-scanner
- 用C语言编写的 单片机驱动条形码扫面议扫描条形码,并在液晶上显示,打印机打印出来的程序。-Microcontroller C language driven barcode scanning the Negotiable scan the bar code, and displayed on the LCD, the printer to print out the program.
main
- msp430扫码及数码管16位显示,生成c文件。-msp430 scan code and 16-bit digital tube display
74HC164-program
- 74HC164 8位移位寄存器编程C代码 扫描LED 数码管,按键都搞定-74HC164 8-bit shift register programming C code Scan LED digital tubes, buttons are buttoned